Korg D8 manual Track Status, 22. EQ, Effect Send

Page 57

21. TRACK STATUS

Track status select .....................................................

[PLAY, REC (ANALOG), REC (DIGITAL), Mute]

Selects the status of each track.

✧Each time you press the [TRACK STATUS] key, the function will change and the indicator color will change to show this.

PLAY (indicator lit green): The selected track can be played back.

REC (ANALOG) (indicator blinking/lit red): This can be selected when [REC SELECT] is INPUT 1/2 or MASTER. Audio from the external input jacks INPUT 1/2 or from the master bus can be recorded to the selected track. The indicator will blink during record- ready condition, and will light during recording (or rehearsal).

REC (DIGITAL) (indicator blinking/lit orange): This can be selected when [REC SELECT] is DIGITAL IN. The external input from the DIGITAL IN connector can be recorded to the selected track. The indicator will blink during record-ready condition, and will light during recording (or rehearsal).

It is not possible to input from the internal effect or from an external input via the AUX IN jacks.

MUTE (indicator off): The selected track will be muted.

When input monitor (refer to p.47) is set to AUTO, set- ting [TRACK STATUS] to REC will cause the EQ and fader to apply only to the input sound, so that the fader and EQ will not affect the playback sound of the track. Be aware that if you inadvertently change the fader or EQ settings during playback etc., the volume or EQ of the input sound will be affected.

However if [REC SELECT] is set to MASTER, it will be the same as when [TRACK STATUS] is set to PLAY; you will always hear the playback tracks, and faders and EQ will be valid.

22. EQ

P1 High EQ gain adjustment

1 2

HEQ1 :+00

P1-1 Channel number display...........................................

[1, 2, 3, 4, 5, 6, 1-2, 3-4, 5-6, 7-8]

This shows the currently selected channel number.

1-2, 3-4and 5-6will appear when Pairing is On (refer to PAIR On/Off).

P1-2HEQ (Fc=10 kHz) gain setting

[-15...+00...+15]

The boost/cut at the 10 kHz cutoff frequency can be adjusted over a range of -15–+15 dB.

P2 Low EQ gain adjustment

1 2

LEQ1 :+00

P2-1Channel number display ..................................

[1, 2, 3, 4, 5, 6, 1-2, 3-4, 5-6, 7-8]

This shows the currently selected channel number.

1-2, 3-4and 5-6will appear when Pairing is On (refer to PAIR On/Off).

P2-2LEQ (Fc=100 Hz) gain setting

[-15...+00...+15]

The boost/cut at the 100 Hz cutoff frequency can be adjusted over a range of -15–+15 dB.

High EQ and Low EQ can be paired (refer to PAIR On/ Off), and registered as part of a scene (refer to SCENE).

TRACK STATUS=REC Recording

FADER

INPUT [EQ]

TRACK

HEQ LEQ

TRACK STATUS=REC Playback

FADER

INPUT

[EQ]

TRACK

HEQ LEQ

TRACK STATUS=PLAY Playback

FADER

INPUT

[EQ]

TRACK

EQ and fader will apply to the input sound and will affect the recording

EQ and fader will not affect the playback

EQ and fader will apply to the playback

23. EFFECT SEND

P1 Effect send level (Snd) adjustment

Adjusts the level that is sent from after each channel fader (post fader) to the internal effect.

Adjust this setting when you use the internal effect.

When [REC SELECT] DIGITAL IN is selected, the internal effect will be off.

1 2

Snd1 :000

HEQ LEQ

Pairing (refer to PAIR On/Off) is also possible.

58

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Page Table of Contents Moving and storing time locations Adjusting and storing mixer settingsSynchronization and control with a Midi Saving to and loading from DATOperation Power on/off Connections, Power-on, DemoConnections to your audio system etc Turning the power off Turning the power onListening to the demo songs 01ScukyllCreating a new song Naming a songCreating and selecting songs Recording analog record- ing Connecting the input device and adjusting the level03KORG1 Starting and stopping recordingAdjusting the EQ Using EQ to modify the tone as you recordRecording digital recording BackSelecting the effect program Selecting the location at which the effect will be insertedEditing the effect Saving the effect programMaster Send Type Sending the input sound to the effectApplying the dedicated delay to the input sound Turning the monitor delay on/offEditing the monitor delay Select the playback/recording tracks Select the input monitorMonAuto Undo Auto Punch In/OutRedo Storing the in and OUT timesAuto punch in/out setting PstRol02MRehearsing auto punch in/out Combining multiple tracks into one or two tracks Bounce Playback track and recording track settingsApplying EQ and effects while you record Adjusting the playback level and recording levelListening to the metro- nome while you record Playback Trigger recordingApplying an effect to the playback sound Selecting the tracks for playbackSending the playback sound to the external effect Program playback of songs Switching scenes dur- ing playbackMoving and storing time locations Moving the current timeLocate points LOC1, LOC2, LOC3 Finding a precise time locationStoring a Mark point Mark pointsMarkùM001 Moving to a Mark pointAdjusting the volume of each channel Pairing settingsPairing on/off Enabling parameters for pairingUsing the EQ to adjust the tone Adjusting the stereo locationAdjusting the Effect Send, AUX Send and Track Status Adjusting the High EQScene Switching scenes during a songStoring a scene Recalling a sceneApplying an effect dur- ing mixdown Recording a master tape MixdownCopying track data Track Copy Storing IN, OUT and to timesEditTrackú CpyTr 1 ¿¿TrCLP Ï CpyTrCLPÏ¿¿Tr 1x 1Ï Erasing data from a track Erase Track Inserting a blank space into the track data Insert TrackInserting a blank space into the IN-OUT area of a track Ins¿Tr 1?Deleting data from the IN-OUT area of a track Deleting data from a track Delete TrackDel¿Tr 1? Swapping the IN-OUT areas of two tracksCopying a song Song RecoverMoving a song Deleting a songRecording Midi Clock data from a sequencer Tempo map settingsCreating a tempo map Deleting a tempo mapSelecting the tempo source Recording tap tempoUsing Midi Clock to synchronize a Midi sequencer to the D8 Using MTC to synchroTo the D8 Nize a Midi sequencerConnecting an external drive Using MMC to control the D8 from a Midi sequencerRcvMMCo Ï DevID 01ÏExchanging disks on a removable disk drive Initializing and format- ting a driveSaving a song on a removable disk drive Backup InsNextDsk Restore ÏARM 100 ¿ A01SngNa¿Backup Ï Saving a song to a DAT recorder Backup¿HDAT100Ï ¿DATokÏLoading a backed-up song from a DAT recorder Restore Loading a backed-up song from a DAT recorder RestoreHDAT100 ¿ PlayDAT ÏReference Edit SONG/TRACK SONG/TRACKP1 Song number/name display Drive/song selectDelI01okœ RenamA01œ SngName œMovøI01okœ CpyI1-35ø øB06-40okœCpyTr ØTr 1x99œ P3 Edit TrackSystem Edit System P2 MIDI/SYNC settingsDeleting a mark Input 1/2 assignDiskUtil œ Song backupARM 100 œ Drive informationRestore œ ARM 100 ø A01SngN ø ØB02NoDA Song restoreØBHD1300œ Initialize/formatREC Mode Display ModePlay Mode P1 Counter display selectionP1 Pre roll time setting Edit Play ModeP2 Post roll time setting TriggerP2 Pre trigger time setting P1 Threshold level adjustmentP1 Tempo map settings Edit TriggerP1 Tempo source setting P2 Metronome volume settingEdit Tempo MetronomeP2 Metronome mode setting P1 Metronome volume settingEdit Metronome 15. IN/LOC1, OUT/LOC2, TO/LOC3Edit Scene SceneP1 Scene parameter list P2 Deleting a sceneScrub StoreUndo P1 Storing IN/LOC 1, OUT/LOC 2, TO/LOC 3 or a SceneTrack Status 22. EQEffect Send PAN/BALANCE P2 External output Aux level settingFader OffPair On/Off P1-1 Pairing on/offREC Select Snd1-2000Effect RD1...SE9 Factory Preset, U01...U65 User AreaP1 Effect select P1-1Effect program category number selectP2-3Monitor delay parameter settings P2 Monitor delay settingsP2-1 Monitor delay on/off 200msœP1 Editing and saving an effect Edit EffectLoG-15dBœ All Effo RenøRoomEdit Effect Assign Effect AssignAppendices TroubleshootingMidi sequencer does not synchronize to the D8 Various messages Midi Implementation Chart Block Diagram Effect Assign = Input 1/2 Type EFFECT1 EFFECT2 EFFECT3 EFFECT4 Effect Program List4BEQ 4 Band Equalizer Effect Parameter ListNR Noise Reduction Phono Turntable SIM Demo Song List Metronome Type ListScukyll Express Moonlit sea written by Yuko AsaiD8 Specifications Bouncing tracks Functions added to the D8
Top Page Image Contents