Korg D8 manual Edit Trigger, Tempo, P1 Threshold level adjustment, P2 Pre trigger time setting

Page 52

10. EDIT TRIGGER

P1 Threshold level adjustment

1

ThrLev:050

P1-1Threshold level adjustment

[001...100]

When trigger recording is used, this parameter speci- fies the audio input level that will initiate recording. When in record ready mode, recording will begin when this level is exceeded.

Since the appropriate level will depend on the source that is being input, try various threshold level settings to find the best setting.

P2 Pre trigger time setting

1

PrTrg:000m

P2-1Pre trigger time setting

[000...700 m (s)]

Specifies the pre trigger time during which the sound will be recorded before the actual trigger time.

When trigger recording is used, the initial part of the sound may be lost for sounds with a rapid attack, such as percussion.

By setting the pre trigger time, you can enable the recording to include the low-volume portion that is heard before the trigger threshold level is reached.

Since the appropriate time setting will depend on the source that is being input, try various pre trigger times to find the best setting.

At the beginning of the song, this will have no effect.

If you begin recording at the end of a previously recorded track, setting the pre trigger time to other than 000 ms will cause the recording to overlap part of the previously recorded sound, causing the end of that sound to be cut off.

Trigger on

Threshold level

Pre trigger time

Recording start location

11. TEMPO

P1 Tempo map settings

Specifies the tempo and time signature of the song.

If you wish to listen to the metronome sound while you set the tempo, turn on the metronome (refer to METRONOME) before entering this page.

 

1

 

2

 

3

 

5

 

 

2:120—4/4œ

œ:Metro4 œ

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

P1-1 Tempo map number select

[0 9]...

Selects the tempo map number

0: This is the basic tempo map placed at the beginning of the song. It is not possible to specify the location (P1-4) for this.

1...9: These are tempo maps which can be placed else- where than the beginning of the song. Select these when you wish to change the tempo or time signature in the middle of a song.

P1-2 Tempo setting

[40...240, (Trk)]

Specifies a song tempo of q =40–240.

This parameter can be set if Map has been selected as the tempo source (refer to EDIT TEMPO P1).

If Trk has been selected as the tempo source, this page will indicate Trk, and it will not be possible to specify the tempo. In this case, playback (recording) will occur at the tempo which was recorded during tempo recording (refer to EDIT TEMPO P2).

If you modify the tempo after recording, the measures and time signature shown in the location counter will no longer match the audio in the tracks. In order to bring these back into correspondence, use Tap Tempo recording (refer to EDIT TEMPO).

P1-3

Time signature setting

[1...8/4, 10/4,

 

1...

8/8, 10/8, 12/8, 16/8, 1...

8/16, 10/16, 12/16, 16/16]

 

Specifies the time signature.

 

P1-4

Map location setting

[000 (Delete Map),

 

001...999 Meas (set in measure units)]

Specifies the location of the tempo map (i.e., the time at which the setting will begin to change). Simulta- neously press the [ ] and [ ] keys to move to the location counter.

This cannot be set if the tempo map number (P1-1) is 0.

000: Select this when you wish to delete the tempo map. Select 000 for the tempo map that you wish to delete, and it will be deleted when you exit this page.

001...999: Specify the location in the range of measure 1–999.

You can move a tempo map regardless of the location of earlier or later tempo maps.

However when you exit P1, tempo map numbers (P1-

1)will be automatically renumbered from low to high, starting from the beginning of the song (i.e., based on the time location within the song).

Chapter 3

Reference

 

 

 

 

53

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Page Table of Contents Adjusting and storing mixer settings Moving and storing time locationsSynchronization and control with a Midi Saving to and loading from DATOperation Connections, Power-on, Demo Power on/offConnections to your audio system etc Turning the power on Turning the power offListening to the demo songs 01ScukyllNaming a song Creating a new songCreating and selecting songs Connecting the input device and adjusting the level Recording analog record- ing03KORG1 Starting and stopping recordingUsing EQ to modify the tone as you record Adjusting the EQRecording digital recording BackSelecting the location at which the effect will be inserted Selecting the effect programEditing the effect Saving the effect programSending the input sound to the effect Master Send TypeTurning the monitor delay on/off Applying the dedicated delay to the input soundEditing the monitor delay Select the input monitor Select the playback/recording tracksMonAuto Auto Punch In/Out UndoRedo Storing the in and OUT timesPstRol02M Auto punch in/out settingRehearsing auto punch in/out Playback track and recording track settings Combining multiple tracks into one or two tracks BounceAdjusting the playback level and recording level Applying EQ and effects while you recordListening to the metro- nome while you record Trigger recording PlaybackSelecting the tracks for playback Applying an effect to the playback soundSending the playback sound to the external effect Switching scenes dur- ing playback Program playback of songsMoving and storing time locations Moving the current timeFinding a precise time location Locate points LOC1, LOC2, LOC3Mark points Storing a Mark pointMarkùM001 Moving to a Mark pointPairing settings Adjusting the volume of each channelPairing on/off Enabling parameters for pairingAdjusting the stereo location Using the EQ to adjust the toneAdjusting the Effect Send, AUX Send and Track Status Adjusting the High EQSwitching scenes during a song SceneStoring a scene Recalling a sceneRecording a master tape Mixdown Applying an effect dur- ing mixdownStoring IN, OUT and to times Copying track data Track CopyEditTrackú CpyTr 1 ¿CpyTrCLPÏ¿ ¿TrCLP Ï¿Tr 1x 1Ï Inserting a blank space into the track data Insert Track Erasing data from a track Erase TrackInserting a blank space into the IN-OUT area of a track Ins¿Tr 1?Deleting data from a track Delete Track Deleting data from the IN-OUT area of a trackDel¿Tr 1? Swapping the IN-OUT areas of two tracksSong Recover Copying a songMoving a song Deleting a songTempo map settings Recording Midi Clock data from a sequencerCreating a tempo map Deleting a tempo mapRecording tap tempo Selecting the tempo sourceUsing MTC to synchro Using Midi Clock to synchronize a Midi sequencer to the D8To the D8 Nize a Midi sequencerUsing MMC to control the D8 from a Midi sequencer Connecting an external driveRcvMMCo Ï DevID 01ÏInitializing and format- ting a drive Exchanging disks on a removable disk driveSaving a song on a removable disk drive Backup Restore Ï InsNextDskARM 100 ¿ A01SngNa¿Saving a song to a DAT recorder Backup Backup Ï¿HDAT100Ï ¿DATokÏLoading a backed-up song from a DAT recorder Restore Loading a backed-up song from a DAT recorder RestoreHDAT100 ¿ PlayDAT ÏReference SONG/TRACK Edit SONG/TRACKP1 Song number/name display Drive/song selectRenamA01œ SngName œ DelI01okœMovøI01okœ CpyI1-35ø øB06-40okœP3 Edit Track CpyTr ØTr 1x99œSystem P2 MIDI/SYNC settings Edit SystemDeleting a mark Input 1/2 assignSong backup DiskUtil œARM 100 œ Drive informationSong restore Restore œ ARM 100 ø A01SngN ø ØB02NoDAØBHD1300œ Initialize/formatDisplay Mode REC ModePlay Mode P1 Counter display selectionEdit Play Mode P1 Pre roll time settingP2 Post roll time setting TriggerP1 Threshold level adjustment P2 Pre trigger time settingP1 Tempo map settings Edit TriggerP2 Metronome volume setting P1 Tempo source settingEdit Tempo MetronomeP1 Metronome volume setting P2 Metronome mode settingEdit Metronome 15. IN/LOC1, OUT/LOC2, TO/LOC3Scene Edit SceneP1 Scene parameter list P2 Deleting a sceneStore ScrubUndo P1 Storing IN/LOC 1, OUT/LOC 2, TO/LOC 3 or a Scene22. EQ Track StatusEffect Send P2 External output Aux level setting PAN/BALANCEFader OffP1-1 Pairing on/off Pair On/OffREC Select Snd1-2000RD1...SE9 Factory Preset, U01...U65 User Area EffectP1 Effect select P1-1Effect program category number selectP2 Monitor delay settings P2-3Monitor delay parameter settingsP2-1 Monitor delay on/off 200msœEdit Effect P1 Editing and saving an effectLoG-15dBœ All Effo RenøRoomEffect Assign Edit Effect AssignTroubleshooting AppendicesMidi sequencer does not synchronize to the D8 Various messages Midi Implementation Chart Block Diagram Effect Assign = Input 1/2 Effect Program List Type EFFECT1 EFFECT2 EFFECT3 EFFECT4Effect Parameter List 4BEQ 4 Band EqualizerNR Noise Reduction Phono Turntable SIM Metronome Type List Demo Song ListScukyll Express Moonlit sea written by Yuko AsaiD8 Specifications Functions added to the D8 Bouncing tracks
Top Page Image Contents