Korg D8 manual Select the playback/recording tracks, Select the input monitor, MonAuto

Page 13

7.Listening to recorded tracks while you record another track (Overdubbing)

The process of recording additional tracks while you listen to previously recorded tracks is called “overdubbing”.

As an example, we will explain how you can play- back the sound that was recorded on track 1, and perform analog recording on track 2.

■Select the playback/recording tracks

1Press the track 1 [TRACK STATUS] key several times to select PLAY (indicator lit green), to enable (the previously recorded) track 1 for playback.

lit green

blinking red

1

2

L

R

2Press the track 2 [TRACK STATUS] key to select REC (ANALOG) (indicator blinking red), to enable it as the recording track.

3Either turn down [CHANNEL] faders 3–7/8, or press their [TRACK STATUS] keys several times to select MUTE (indicator off), to mute these tracks so that they will not sound during playback.

■Connecting the input device for the record- ing track and adjusting the level

4As shown in “■ Connecting the input device and adjusting the level” (p.11, p.12), connect an instru- ment etc. to the INPUT 1 jack, and set the input level.

5Raise or lower the [CHANNEL] fader of the play- back track to a volume that will be comfortable for playing along with.

■Starting and stopping recording

6Press the [REC] key, and then press the [PLAY] key to begin recording. Press the [STOP] key to stop recording. (Refer to “■ Starting and stopping recording”, p.11)

■Listening to the recorded performance (Play- back)

7Move the current time to a location earlier than the point at which you began recording. Then set the [TRACK STATUS] of the recorded track to PLAY, and press the [PLAY] key to begin playback. Press the [STOP] key to stop playback. (Refer to “■ Listening to the recorded performance (Play- back)”, p.11)

8.Manually re-recording part of the performance (Manual Punch In/Out)

If you made a mistake during the performance that you recorded, or if you were not able to play the entire song as you had intended, there is no need to re-record the entire song — you can re-record just the part that you need.

“Punch In” is the action of switching from song playback to record, and “Punch Out” is the action of switching back from recording to playback.

“Manual Punch In/Out” is when you perform the Punch In and Punch Out manually. On the D8, you can Punch In during playback either by pressing the [REC] key or by pressing a foot switch <sold separately>. You can Punch Out by pressing either the [REC] key or the [PLAY] key, or by pressing a foot switch.

Begin recording

Stop recording

 

(playback)

(recording)

(playback)

 

REC

REC

PLAY

 

 

 

or

or

or

 

Foot switch

 

Foot switch

■Connecting the input device and adjusting the level

1As explained in “■ Connecting the input device and adjusting the level” (p.12), connect the input device and adjust the level. At this time, make adjustments so that there is no difference between the volume of the instrument that is being input and the volume of the track.

■Select the input monitor

2Press the [SYSTEM] key several times (indicator lit) to access the “Mon” display. Then rotate the [VALUE] dial to select Auto.

Mon:Auto

SYSTEM

E

■Starting and stopping recording

3Move the current time location to a point earlier than the location that you wish to re-record. If you hold down the [STOP] key and press the [REW] key, you will move to the beginning of the song.

4Press the [PLAY] key (indicator lit) to begin playback.

The [TRACK STATUS] indicator which

2

was set to REC will blink, and you will

R

 

hear the sound of the track.

 

For tracks whose [TRACK STATUS] is set to REC, the EQ and fader will affect only the input sound, and will not affect the playback sound. After adjusting the input level, do not modify the fader or EQ settings during playback, since this will change the volume and EQ of the input sound.

5When you wish to begin re- REC recording, press the [REC] key

(Manual Punch In). The

2

[TRACK STATUS] indicator will

R

 

16

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Page Table of Contents Moving and storing time locations Adjusting and storing mixer settingsSynchronization and control with a Midi Saving to and loading from DATOperation Connections, Power-on, Demo Power on/offConnections to your audio system etc Turning the power off Turning the power onListening to the demo songs 01ScukyllNaming a song Creating a new songCreating and selecting songs Recording analog record- ing Connecting the input device and adjusting the level03KORG1 Starting and stopping recordingAdjusting the EQ Using EQ to modify the tone as you recordRecording digital recording BackSelecting the effect program Selecting the location at which the effect will be insertedEditing the effect Saving the effect programMaster Send Type Sending the input sound to the effectTurning the monitor delay on/off Applying the dedicated delay to the input soundEditing the monitor delay Select the input monitor Select the playback/recording tracksMonAuto Undo Auto Punch In/OutRedo Storing the in and OUT timesPstRol02M Auto punch in/out settingRehearsing auto punch in/out Combining multiple tracks into one or two tracks Bounce Playback track and recording track settingsApplying EQ and effects while you record Adjusting the playback level and recording levelListening to the metro- nome while you record Playback Trigger recordingSelecting the tracks for playback Applying an effect to the playback soundSending the playback sound to the external effect Program playback of songs Switching scenes dur- ing playbackMoving and storing time locations Moving the current timeLocate points LOC1, LOC2, LOC3 Finding a precise time locationStoring a Mark point Mark pointsMarkùM001 Moving to a Mark pointAdjusting the volume of each channel Pairing settingsPairing on/off Enabling parameters for pairingUsing the EQ to adjust the tone Adjusting the stereo locationAdjusting the Effect Send, AUX Send and Track Status Adjusting the High EQScene Switching scenes during a songStoring a scene Recalling a sceneApplying an effect dur- ing mixdown Recording a master tape MixdownCopying track data Track Copy Storing IN, OUT and to timesEditTrackú CpyTr 1 ¿CpyTrCLPÏ¿ ¿TrCLP Ï¿Tr 1x 1Ï Erasing data from a track Erase Track Inserting a blank space into the track data Insert TrackInserting a blank space into the IN-OUT area of a track Ins¿Tr 1?Deleting data from the IN-OUT area of a track Deleting data from a track Delete TrackDel¿Tr 1? Swapping the IN-OUT areas of two tracksCopying a song Song RecoverMoving a song Deleting a songRecording Midi Clock data from a sequencer Tempo map settingsCreating a tempo map Deleting a tempo mapSelecting the tempo source Recording tap tempoUsing Midi Clock to synchronize a Midi sequencer to the D8 Using MTC to synchroTo the D8 Nize a Midi sequencerConnecting an external drive Using MMC to control the D8 from a Midi sequencerRcvMMCo Ï DevID 01ÏExchanging disks on a removable disk drive Initializing and format- ting a driveSaving a song on a removable disk drive Backup InsNextDsk Restore ÏARM 100 ¿ A01SngNa¿Backup Ï Saving a song to a DAT recorder Backup¿HDAT100Ï ¿DATokÏLoading a backed-up song from a DAT recorder Restore Loading a backed-up song from a DAT recorder RestoreHDAT100 ¿ PlayDAT ÏReference Edit SONG/TRACK SONG/TRACKP1 Song number/name display Drive/song selectDelI01okœ RenamA01œ SngName œMovøI01okœ CpyI1-35ø øB06-40okœCpyTr ØTr 1x99œ P3 Edit TrackSystem Edit System P2 MIDI/SYNC settingsDeleting a mark Input 1/2 assignDiskUtil œ Song backupARM 100 œ Drive informationRestore œ ARM 100 ø A01SngN ø ØB02NoDA Song restoreØBHD1300œ Initialize/formatREC Mode Display ModePlay Mode P1 Counter display selectionP1 Pre roll time setting Edit Play ModeP2 Post roll time setting TriggerP2 Pre trigger time setting P1 Threshold level adjustmentP1 Tempo map settings Edit TriggerP1 Tempo source setting P2 Metronome volume settingEdit Tempo MetronomeP2 Metronome mode setting P1 Metronome volume settingEdit Metronome 15. IN/LOC1, OUT/LOC2, TO/LOC3Edit Scene SceneP1 Scene parameter list P2 Deleting a sceneScrub StoreUndo P1 Storing IN/LOC 1, OUT/LOC 2, TO/LOC 3 or a Scene22. EQ Track StatusEffect Send PAN/BALANCE P2 External output Aux level settingFader OffPair On/Off P1-1 Pairing on/offREC Select Snd1-2000Effect RD1...SE9 Factory Preset, U01...U65 User AreaP1 Effect select P1-1Effect program category number selectP2-3Monitor delay parameter settings P2 Monitor delay settingsP2-1 Monitor delay on/off 200msœP1 Editing and saving an effect Edit EffectLoG-15dBœ All Effo RenøRoomEdit Effect Assign Effect AssignAppendices TroubleshootingMidi sequencer does not synchronize to the D8 Various messages Midi Implementation Chart Block Diagram Effect Assign = Input 1/2 Type EFFECT1 EFFECT2 EFFECT3 EFFECT4 Effect Program List4BEQ 4 Band Equalizer Effect Parameter ListNR Noise Reduction Phono Turntable SIM Demo Song List Metronome Type ListScukyll Express Moonlit sea written by Yuko AsaiD8 Specifications Bouncing tracks Functions added to the D8
Top Page Image Contents