Cisco Systems 30 VIP manual SDLTraceTypeFlag Value Definition, SDLTraceDataFlag Value

Page 17

Cisco IP Telephony Troubleshooting Guide for Cisco CallManager Release 3.0(1)

SdlTraceTypeFlags Definitions

SDLTraceTypeFlag Value

Definition

traceLayer1

TraceDetailLayer1

TraceSdlLinkAdmin

traceUnused

traceLayer2

traceLayer2Interface

traceLayer2TCP

TraceDetailLayer2

traceLayer3

traceCc

traceMiscPolls

traceMisc

traceMsgtrans

traceUuie

traceGateway

=0x00000001

=0x00000002

=0x00000004

=0x00000008

=0x00000010

=0x00000020

=0x00000040

=0x00000080

=0x00000100

=0x00000200

=0x00000400

=0x00000800

=0x00001000

=0x00002000

=0x00004000

All Layer 1 trace on

Detail Layer 1 trace on

Trace inter-Cisco CallManager links within a cluster

Not used

All Layer 2 trace on

Layer 2 interface trace on

Layer 2 TCP trace on

More detail dump of Layer 2 Frames.

All Layer 3 trace on

All call control trace on

Trace miscellaneous polls

Miscellaneous trace on (Database signals)

Message Translation signals (TranslateIsdnToSdlReq, TranslateIsdnToSdlRes TranslateSdlToIsdnReq, TranslateSdlToIsdnRes)

UUIE output trace on

Gateway signals

Data bits described in the following table are set in the Service > Service Parameters area in Cisco CallManager Administration. Following are two examples of desired values based on the particular problem.

The recommended value for normal system debugging is SdlTraceDataFlags=0x110

The recommended value when tracking problems with SDL links is 0x13D (non- compacted trace; if a compact trace is desired, bit 0x200 must be set. It can be set in combination with any other bits)

SDLTraceDataFlags Definitions

SDLTraceDataFlag Value

TraceSdlLinkState

= 0x001

TraceSdlLowLevel

= 0x002

 

 

TraceSdlLinkPoll

= 0x004

TraceSdlLinkMsg

= 0x008

traceRawData

= 0x010

TraceSdlTagMap

= 0x020

traceCreate

= 0x100

TraceNoPrettyPrint

= 0x200

Disk Space Warning

Definition

Enable trace of SDL Link Initialization

Enable tracing of low-level SDL events, for example, fileOpen, socket events, and so on

Enable tracing of SDL Link Poll message

Enable tracing of SDL Link Message

Enable raw signal data trace on all signals

Enable tag mapping

Enable process create and stop traces

Disable pretty printing of trace files

IMPORTANT: Be advised that information obtained from this interface could be very detailed, and therefore consume a large amount of disk space. For this reason, we advise you to turn on the trace file for a specific amount of time, then review the information and turn off the trace.

© 2000 Cisco Systems, Inc.

17

Image 17
Contents SDI Trace Output Configuring Traces Reorder Tone Through Gateways Gateway Registration Problems Page Purpose Documentation Checklist Channel Calling Search Space CCAPi Acronym/Term Cnf Law mu-lawCisco IOS Cluster Codec ChannelPartition Flow Full duplex 711 729 225 245 323 Half Duplex HookflashJitter Law mu-law Silence Suppression Voice Activation Detection 931Route Filter Route Group Route List Route Pattern Voice Activation Detection Silence Suppression VoIP Translation PatternCisco CallManager Administration Details View Report Microsoft PerformanceMicrosoft Event Viewer SDI Trace Configuring Traces SDL Trace Page SDLTraceDataFlag Value SDLTraceTypeFlag Value DefinitionCall Detail Records CDR and Call Management Records CMR Sniffer TraceSelect Service Service Parameters CDRs Voice Quality Problem CategoriesPage Packet Number Time absolute ms Time delta ms Button Help John Check Your Loads Phone Resets Dropped Calls Page Page Cisco CallManager Feature Issues Locations Conf Bridge Region1 Region2 MTP Resource Problems MTP Dial Plans Dialing DOES-NOT-EXIST Page DialPlanWizardG Clause NamePattern Device Name Device Description Usage Pattern PartitionReorder Tone Through Gateways Slow Server ResponseGateway Registration Problems Module.port CFG Booting Dhcp for dynamic configurationTracyclose mod port tracystart mod port TaskID Cmd show dhcp Gmsg ***TFTP Error File Not Found Gmsg CCM#0 CPEvent = Loadid -- CPState = LoadResponse Gatekeeper ProblemsRegistration Rejects RRJ Cisco IP Phone Initialization Process Sample TopologyPage Skinny Station Registration Process Message Description Station Register Station ResetStation IP Port AcknowledgePage Cisco CallManager Initialization Process Self-Starting Processes Cisco CallManager Registration Process Cisco CallManager KeepAlive Process Cisco CallManager Intra-Cluster Call Flow Traces Cisco Systems, Inc CCMStationD stationOutputStopTone tcpHandle=0x4fbbc30 Cisco Systems, Inc Call Flow Traces Page Cisco Systems, Inc Following debug messages show that the call is in progress Gatekeeper Endpoint Registration Debug Messages and Show Commands on the Cisco IOS GatewayCisco Systems, Inc Page Cisco IOS Gateway with T1/PRI Interface Cisco IOS Gateway with T1/CAS Interface Cisco Systems, Inc Inter-Cluster H.323 Communication Call Flow Traces Failed Call Flow Cisco Systems, Inc Reading Records Writing RecordsRemoving Records Table SchemaFields in a Call Detail Record Known IssuesDeciphering the Time Stamp Origination leg call identifier Global Call IdentifierDate/time of call origination Originator’s node IDCalling party cause Of call termination Isdn location valueIP address for the originator’s media connection Port for the originator’s media connectionIP address to which the call was delivered unsigned integer Destination span or portIP port to which the call was delivered Called party’s partitionCodec type used by the destination on sending side IP address for the destination outgoing media connectionDate/time of connect Date/time of disconnect unsigned integerCisco CallManager node identifier Global Call Identifier for this callCall Identifier Directory number used on this callLatency experienced during this connection Lost RTP packets during this connectionInterarrival jitter during this connection Normal Calls Cisco IP Phone-to-Cisco IP Phone Call Management Records Logged By Call Type Codec Cause Codes Description Codec Types Compression / Payload typesNumber changed Alarms Calling Cisco Technical Assistance Center TAC Index Debug messages and show commands Page Topology

30 VIP specifications

Cisco Systems has been a leading company in networking technology, and its suite of products is continually evolving to meet the demands of modern digital infrastructure. One of the latest introductions is the Cisco Systems 30 VIP, a highly advanced solution designed to enhance network performance and security for businesses of all sizes.

The Cisco Systems 30 VIP stands as a cornerstone for next-generation networking features, providing organizations with significant advantages in speed, reliability, and scalability. At the heart of the 30 VIP are key technologies such as advanced routing protocols and enhanced security measures that ensure seamless data transfer across multiple devices.

Main features of the Cisco Systems 30 VIP include its high throughput capabilities, which support accelerated data processing and lower latency. This is crucial for businesses that rely on real-time data exchange and cloud applications. Additionally, the device incorporates Multi-Protocol Label Switching (MPLS) technology, which optimizes data flow between networks and significantly enhances overall performance.

Another notable characteristic of the 30 VIP is its integrated security features, including advanced threat detection and prevention systems. These are designed to protect sensitive business data from cyber threats, ensuring operational continuity and compliance with industry regulations. The Cisco 30 VIP also supports secure access protocols, allowing for secure remote connections, which is increasingly vital in today’s hybrid work environment.

The adaptability of the Cisco Systems 30 VIP is another of its standout aspects. It offers compatibility with existing Cisco infrastructure, making it easier for businesses to adopt new technologies without overhauling their entire system. This modular approach allows for easy upgrades and integration of future technologies, ensuring long-term viability and investment protection.

Furthermore, the Cisco Systems 30 VIP is powered by intelligent network management software that simplifies monitoring, configuration, and troubleshooting processes. This software enhances network visibility, allowing administrators to identify and address potential issues proactively, thereby reducing downtime and enhancing user experience.

In summary, the Cisco Systems 30 VIP represents a significant advancement in network technology with its high throughput, integrated security features, adaptability, and intelligent management capabilities. These elements combine to provide a robust solution that meets the evolving needs of modern businesses while ensuring secure and efficient operations. As organizations continue to navigate an increasingly complex digital landscape, the Cisco Systems 30 VIP offers a future-proof option designed to facilitate growth and resilience.