VTech VT 4121 manual FCC Regulations, Vtech Communications, FCC Part

Page 6

FCC REGULATIONS

This equipment complies with Parts 15 and 68 of the Federal Communications Commission (FCC) rules for the United States. It also complies with regula- tions RSS210 and CS-03 of Industry and Science Canada. Operation is subject to the following two conditions:

1.This device may not cause interfer- ence, and

2.This device must accept any inter- ference, including interference that may cause undesired operation of the device.

A label is located on the underside of the base unit containing either the FCC registration number and Ringer Equivalence Number (REN) or the IC registration number and Load Number. You must, upon request, provide this information to your local telephone company.

This equipment is compatible with inductively coupled hearing aids.

Should you experience trouble with this telephone equipment, please con- tact:

VTECH COMMUNICATIONS

SERVICE DEPT. at 1-800-595-9511.

For repair/warranty information. The telephone company may ask you to disconnect this equipment from the line network until the problem has been corrected.

FCC Part 15

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliances could void the user's authority to operate the equipment.

The equipment has been tested and found to comply with part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a resi- dential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter- ference to radio communications. However, there is no guarantee that interference will not occur in a particu- lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Introduction ICM VolumeALL Mute EnterAdjustable Ringer, Receive and Speaker Volume Levels Message Waiting IndicatorDelayed Ringing Caller ID LogConference Hold with ReminderCall Privacy with Release Call Forward to Other Speaker- phonesParts Check list Foot handset cord Manual Wall mounting screws and anchorsFCC Regulations Vtech CommunicationsFCC Part FCC Regulations Important Safety Instructions Important Safety Instructions Installation Site PlanningDesk/Tabletop Mounting Wall Mounting Installation Extension Number ProgrammingGeneral Programming Guidelines Press ProgramDate and Time CO/PBX Line RingingPress Mute Enter Delayed Ringing CO Line Ring ToneDefault Setting OFF Range Call ForwardSpeed Dial Auto Mute Enable/DisablePress Mute Enter Flash Storing a Telephone Number in Speed Dial Press ProgramStoring a Caller ID Number Erasing the Contents of a Speed Dial Bin Press ProgramPress Mute Enter Reset default Values Line In Use DetectionProgramming Basic Operation Adjusting the Headset Volume Level Adjusting the Handset Volume LevelAdjusting the Speaker Volume Level Adjusting the Ringer Volume LevelAnswering an Outside Call Using the Handset Using the HandsetUsing the Speakerphone / Head Set Using the SpeakerphoneMaking an Intercom Call 12.1 Using the Handset Retrieving a Call on HoldUsing the Speakerphone/Head Set Using the Direct Station ButtonsAnswering an Intercom Call 13.1 Using the Handset Press ICM or SpeakerConferencing Receiving a Transferred CallMuting a Call Two 2 Outside LinesAnswering a Changing Signaling ModesPaging Paging Another Speakerphone To Voice Page All Speaker- phone ExtensionsReceiving a Voice Page to All Speakerphone Extension Using the Flash ButtonUsing the Pause Feature Meet Me Answer to AllPulse-to-Tone Switching Call PrivacyMessage Waiting Light To Program the Area Code Caller ID OperationProgramming the Area Code Press Mute Enter To Erase the Programmed Area CodeReceiving a Number Only Call Receiving a Name and Number CallReceiving Multiple Calls Receiving a Blocked CallReceiving a Call from Outside the Calling Area Reviewing Calls in the Caller ListDelete an Individual Record from the List Delete the Entire Caller ID List Dialing a number form the Caller ID ListSaving a Number to a Speed Dial Key AUX Data Port Avoid rough treatment MaintenanceTaking Care of Your Telephone Avoid waterHOW do I Send MY UNIT, in or OUT of WARRANTY? Warranty StatementWhat does OUR Warranty COVER? For HOW Long After the Original PURCHASE?Technical Specfications VT 4121 SpeakerphoneLine Speakerphone Wall Mounting Template Table of Contents Caller ID Operation Table of Contents Issue
Top Page Image Contents