AT&T 7630 user manual Conecting to a Call With the Speakerphone, Speakerphone Volume Control, Mute

Page 14

TELEPHONE OPERATION

At the Base

Answering a Call

To answer using the Speakerphone, press Kon the base. The SPEAKER light goes on, and the call is connected. To end the call, press Kagain.

Conecting to a Call With the Speakerphone

You can make a call at the handset, and then switch to using the speakerphone.

1Make a call at the handset.

2Press Kon the base to connect to the call.

3Press Pon the handset to disconnect the handset.

4To end the call, press Kon the base.

Speakerphone Volume Control

Press +to increase speakerphone volume. Press -to decrease volume.

Mute

Mute allows you to hear your caller, but prevents the caller from hearing you. To activate the Mute feature, press U. The MUTE light on the base goes on. To deactivate the Mute feature, press Uagain.

Hold

Press H. The speaker light flashes.

To return to the call, press Hagain

— OR —

Press Pon the handset

— OR —

Press K on the base

— OR —

Lift the handset of an extension phone on the same line.

Page/Intercom

1Press the button on the base. This sends a three-part paging tone to the handset.

2When the Ibutton on the handset is pressed and when the INTERCOM/LOW BATT light on the handset goes on, the handset and base can communicate with each other without tying up the telephone line.

3Press Ion the handset to close the intercom connection.

NOTE: The handset RINGER switch must be set to ON to operate this feature.

1 3

7630_book.1AT&T

13

8/12/98, 6:28 PM

Image 14
Contents Part Please read Part 1 Important Product Information Contents Installation Turn answering Telephone line cord Table/Desk Installation Check for dial tone For Wall InstallationSet the dial mode Installation Telephone Operation Voice Security HoldTemporary Tone Page/IntercomRecording a Phone Conversation Power Reserve FeatureHandset Locator Storing a Pause in a Memory Number Telephone MemoryStoring Memory Numbers OR- Press MReplacing a Stored Number Dialing Memory NumbersDialing Number Stored in M1 Memory GuardMute Speakerphone Volume ControlConecting to a Call With the Speakerphone Operating Range Changing ChannelsAnswering System SET-UP Speaker Volume ControlSetting the Clock Turning the System On/OffRecording Your Announcement Announcement OptionsSelecting Your Announcement Ring Select and Toll Saver Feature Set-UpAnnouncement Play/Silent Deleting an AnnouncementAudible Message Alert Remote Access CodePriority Call Signal Changing the Priority Calling Code Base Ringer SettingReviewing Feature Settings Call Screening/Intercept Answering System OperationAnswering Calls Announcement BypassListening to Your Messages Saving MessagesRecording a Memo Message Guard Power Fail Protection SystemDeleting Messages From a Touch Tone Phone Connecting with the Answering SystemFrom the Cordless Handset Voice Help MenuConnect with the answering system Remote Access CommandsPlaying Messages Reviewing your announcement Call ScreeningRecording Outgoing Announcement To monitor a callRemote ON/OFF Recording a Message When System is OffChanging Settings Audible Signals Reviewing SettingsExit Remote Access Handset Batteries Replacing the Handset Battery Pack If the phone does not work at all If you hear two-beep signal when you try to use the handsetCase of Difficulty If you have no dial toneIf you hear other calls while using the phone If you hear noise or interference when using the phoneIf the phone does not ring when you receive a call If you hear noise in the handset and the buttons don’t workIf CL appears in the Message Counter If messages are incompleteIf you have difficulty hearing messages If your outgoing announcement isnt clearAnswering System Operation 7630WC.1AT&T 12/98, 626 PM