AT&T 7630 user manual For Wall Installation, Check for dial tone, Set the dial mode

Page 7

INSTALLATION

NOTE: When the system is first connected to AC power, it begins an automatic initialization routine. After this routine is complete, the Message Counter flashes CL, indicating the clock needs to be set. See “Setting the Clock” in the Answering System Set-up section of this manual.

7Rotate the base antenna so it is fully upright.

8Charge the handset batteries before use.

Place the handset in the base and charge the batteries for 4 hours. The CHARGING light on the base goes on to show the handset is in the right position to charge the batteries.

9Check for dial tone.

After the batteries are charged, pick up the handset. Press P; the PHONE light should go on and you should hear a dial tone. Press Pagain to turn the phone off.

10Set the dial mode.

If you have touch tone service, the phone is ready to use as soon as the batteries are charged.

If you have dial pulse service you’ll need to change the dialing mode. When the phone is off, press P, p, #, #, #, 3to set the dial mode to Dial Pulse. To return to touch tone dialing (with touch tone service), press P, p, #, #, #, 8.

For Wall Installation

The wall mounting bracket is a wedge-shaped plastic piece attached to the bottom of the base. You’ll need to attach this piece so the thickest end of the bracket is facing the floor when you wall-mount the base.

1Follow Steps 1 to 4 in Table/Desk Installation, except do not re- attach the wall mounting bracket.

2Connect the power cord to the telephone.

Plug the power cord into the jack labeled POWER on the back of the base.

3Guide the power cord from the jack through the straight channel on the base.

Let the excess cord extend straight out of the end of the channel that is farthest from the jack.

4Connect the telephone line cord.

Plug one end of the line cord into the jack on the base. Guide the cord from the jack through the curved channel on the bottom of the base. Wrap any excess line cord around the 2 crescent-shaped tabs on the underside of the wall-mounting bracket. (Make sure you leave enough cord free to extend to the wall jack.)

6

7630_book.1AT&T

6

8/12/98, 6:28 PM

Image 7
Contents Part Please read Part 1 Important Product Information Contents Installation Turn answering Telephone line cord Table/Desk Installation Set the dial mode For Wall InstallationCheck for dial tone Installation Telephone Operation Page/Intercom HoldTemporary Tone Voice SecurityHandset Locator Power Reserve FeatureRecording a Phone Conversation OR- Press M Telephone MemoryStoring Memory Numbers Storing a Pause in a Memory NumberMemory Guard Dialing Memory NumbersDialing Number Stored in M1 Replacing a Stored NumberConecting to a Call With the Speakerphone Speakerphone Volume ControlMute Changing Channels Operating RangeTurning the System On/Off Speaker Volume ControlSetting the Clock Answering System SET-UPSelecting Your Announcement Announcement OptionsRecording Your Announcement Deleting an Announcement Feature Set-UpAnnouncement Play/Silent Ring Select and Toll SaverPriority Call Signal Remote Access CodeAudible Message Alert Reviewing Feature Settings Base Ringer SettingChanging the Priority Calling Code Announcement Bypass Answering System OperationAnswering Calls Call Screening/InterceptSaving Messages Listening to Your MessagesDeleting Messages Message Guard Power Fail Protection SystemRecording a Memo Voice Help Menu Connecting with the Answering SystemFrom the Cordless Handset From a Touch Tone PhonePlaying Messages Remote Access CommandsConnect with the answering system To monitor a call Call ScreeningRecording Outgoing Announcement Reviewing your announcementChanging Settings Recording a Message When System is OffRemote ON/OFF Exit Remote Access Reviewing SettingsAudible Signals Handset Batteries Replacing the Handset Battery Pack If you have no dial tone If you hear two-beep signal when you try to use the handsetCase of Difficulty If the phone does not work at allIf you hear noise in the handset and the buttons don’t work If you hear noise or interference when using the phoneIf the phone does not ring when you receive a call If you hear other calls while using the phoneIf your outgoing announcement isnt clear If messages are incompleteIf you have difficulty hearing messages If CL appears in the Message CounterAnswering System Operation 7630WC.1AT&T 12/98, 626 PM