AT&T 7630 Case of Difficulty, If the phone does not work at all, If you have no dial tone

Page 31

IN CASE OF DIFFICULTY

If you have difficulty operating this telephone answering system, try the sugges- tions below. If you still have trouble, call 1 800 722-9125.

If the phone does not work at all

•Make sure the power cord is plugged into the base and an electrical outlet.

•Make sure the telephone line cord is plugged firmly into the base unit and the telephone jack.

•If the phone does not beep or beeps four times when you press P, the batteries might need recharging.

•If the LOW BATT light is flashing, the batteries need recharging.

•Make sure the handset battery pack is installed correctly.

•If the battery pack still will not charge, replace it with replacement battery 4051.

•If the above suggestions do not solve the problem, try resetting the security code, as described below.

•Place the handset in the base, and check to make sure the CHARG-

ING light is on. Wait 15 seconds, then pick up the handset and press P. The phone should operate properly. If it doesn’t, try the next step.

•Place the handset in the base, and check to make sure the CHARG- ING light is on. Unplug the AC adapter from the outlet, wait 15

seconds, then plug it in again. The CHARGING light should go on. Wait another 15 seconds, then pick up the handset and press P. The phone should operate properly. If it doesn’t, try the next step.

•Pick up the handset, open the battery compartment, and unplug the battery pack. Wait 15 seconds, then reinstall the battery pack, close the battery compartment, and place the handset in the base.

The CHARGING light should go on. Wait another 15 seconds, then pick up the handset and press P. The phone should operate properly.

If you hear two-beep signal when you try to use the handset

•The handset and base are not communicating properly. You might be out of range while attempting to dial. Move closer to the base and try the call again.

•If moving closer to the base does not help, the handset and base might be set to different security codes. Reset the security code, described in the section above.

If you have no dial tone

Check all the previous suggestions. If you still do not hear a dial tone, disconnect the phone and try another one in the same jack. If there is no dial tone on that phone either, the problem is probably in your wiring or local service. Call your local telephone service company.

3 0

7630_book.1AT&T

30

8/12/98, 6:29 PM

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Part Please read Part 1 Important Product Information Contents Installation Turn answering Telephone line cord Table/Desk Installation Set the dial mode For Wall InstallationCheck for dial tone Installation Telephone Operation Page/Intercom HoldTemporary Tone Voice SecurityHandset Locator Power Reserve FeatureRecording a Phone Conversation OR- Press M Telephone MemoryStoring Memory Numbers Storing a Pause in a Memory NumberMemory Guard Dialing Memory NumbersDialing Number Stored in M1 Replacing a Stored NumberConecting to a Call With the Speakerphone Speakerphone Volume ControlMute Changing Channels Operating RangeTurning the System On/Off Speaker Volume ControlSetting the Clock Answering System SET-UPSelecting Your Announcement Announcement OptionsRecording Your Announcement Deleting an Announcement Feature Set-UpAnnouncement Play/Silent Ring Select and Toll SaverPriority Call Signal Remote Access CodeAudible Message Alert Reviewing Feature Settings Base Ringer SettingChanging the Priority Calling Code Announcement Bypass Answering System OperationAnswering Calls Call Screening/InterceptSaving Messages Listening to Your MessagesDeleting Messages Message Guard Power Fail Protection SystemRecording a Memo Voice Help Menu Connecting with the Answering SystemFrom the Cordless Handset From a Touch Tone PhonePlaying Messages Remote Access CommandsConnect with the answering system To monitor a call Call ScreeningRecording Outgoing Announcement Reviewing your announcementChanging Settings Recording a Message When System is OffRemote ON/OFF Exit Remote Access Reviewing SettingsAudible Signals Handset Batteries Replacing the Handset Battery Pack If you have no dial tone If you hear two-beep signal when you try to use the handsetCase of Difficulty If the phone does not work at allIf you hear noise in the handset and the buttons don’t work If you hear noise or interference when using the phoneIf the phone does not ring when you receive a call If you hear other calls while using the phoneIf your outgoing announcement isnt clear If messages are incompleteIf you have difficulty hearing messages If CL appears in the Message CounterAnswering System Operation 7630WC.1AT&T 12/98, 626 PM
Top Page Image Contents