Trilogy Touch Technology 9 4 500-25-00 E1 Network Link Card, 5 500-10 Series MISC. I/O GPI Cards

Page 14

Commander Installation Guide

2.4.4500-25-00 E1 NETWORK LINK CARD

This optional card has a number of front mounted LEDs and a D9 programming socket. The system will normally be assembled by Trilogy with the appropriate rear connector units (RCU). Check the rear of the frame for the Network RCU (500-26-00) which is fitted with two RJ45 connectors and a single BNC. Fit any Network cards in the correct places.

•Inter-system connections are described in Section 4.1.. Operation of the LEDs is described in Section 3.4.5.3.

2.4.5500-10 SERIES MISC. I/O (GPI) CARDS.

This optional board has an LED bar graph array plus a number of miniature rotary switches on the front panel. The system frame will normally be assembled by Trilogy with appropriate rear connector units (RCU). Check the rear of the frame for the Misc. I/O RCU, which is fitted with 25 way and 37 way connectors, and then fit the 500-10 in the correct places.

•Input and output connector pin-outs are given in Section 3.4.5.

•Suggested external input and output circuitry is shown in Section 3.4.5.2.

•Operation of the front panel rotary switches and LEDs is described in Section 3.4.5.1.

•Further information about the on-board links may be found in the Commander Technical Manual.

•Talkback controller types 500-02-11 and 500-02-12 support a maximum of six 500-10-00 GPI cards.

Page 14 of 81

Issue 9

Trilogy Communications Limited

Image 14

Contents Installation Guide 50096601.doc Issue Date Reason for Change ApprovedDocument Number Errata Sheet DescriptionContents Introduction Control Panels Legacy Hardware Options Available and Module Type Numbers Commander Installation Guide Issue Rack Mounting IntroductionUnpacking System Assembly 500-08-10 Changeover Module 1 500-08 Series Changeover CardCommander Installation Guide Commander Installation Guide 4 500-25-00 E1 Network Link Card 5 500-10 Series MISC. I/O GPI Cards6 500-06 Series Matrix Cards D9 Fixed Plug Pin Function Mains Connection and Fusing1 500-15-30 Series Power Supply XLR4 Fixed Socket Pin FunctionStarting the System Commander Installation Guide Connection VIA a PC COM Port Using RS232 Connecting the Matrix PortsConnecting the PC to the Commander System Sub D 9 free female Connection VIA a 500-16-03 Download Converter BOXSub D 9 free female Sub D 9 free male Installing Pathfinder 574 not 576 for a six frame system Matrix Ports RJ-45 Camera ConnectorOther Matrix Connections Alarms RS232 configurationRS422 configuration Serial Link RS232 / RS422Miscellaneous I/O Card Connector PIN-OUT Commander D37 Fixed Plug Pin DescriptionCommander D9 Fixed Socket Pin Description Commander D25 Fixed Socket Upper Connector Pins DescriptionCommander D25 Fixed Socket Lower Connector Pins Description 5.1 500-10 Switches and Indicators Suggested external wiring of Misc I/O card output 5.3 500-25 Network Card Indicators and Switches LEDConfiguring the Gain of Camera Inputs .5.1 Link Setting on Connecting Networked Systems 1 500-26 Network Rear Connector Unit RCUEither Serial Networking Commander Installation Guide Issue Current Range Control Panel Facility Comparison Table 500-41-XX Series Desktop Panels Specification RJ-45 Function Pin 2 500-3X-5X Series Standard Control Panel Rear ViewExpansion Port RJ45 socket Matrix and Expansion RJ45 socket view from rear of panelKeypad D9 Fixed Socket -51 variant only Gpio Local logic in and out D9 Fixed SocketAudio I/O D15 Fixed Socket View of Keypad front panel4 500-3X-5X Series DIP Switch Settings OFFRear Connector Layout Matrix RJ-45 fixed socket on panel Rear Connecor Layout ConnectionsExpansion out RJ-45 fixed socket on panel Gpio Local logic in and out D9 Fixed Socket Control Panel Gpio External Circuitry Keypad D9 Fixed SocketView of Keypad as seen on front panel Rear Panel Layout Connector types500-31-60 Standard Facility 16 KEY Control Panel Headset 5 Pin XLR Fixed Socket front panelGpio Local logic in and out D9 Fixed Socket 10 500-33-00 / 500-45-00 / 500-46-00 Range Gpio Local logic in and out D9 Fixed Socket Commander Installation Guide Issue Ttprog Software 6.2.1 SET-UP Routine Starting the Programme 4.3 500-3x-3x Control Panels Connecting the Hardware4.2 500-02-1x Talkback Controller Programming with the 500-16-03 Download Converter Commander Programming Cable Way D Male Way D Female4.4 500-08-10 Changeover Card Beltpacks RM15TPD-12STelephone Interfaces Connector Detail per channelConnector Detail Trilogy 500-19-10 Telephone Interface FrameTelos ONE Alignment RT Equipment 500-22-00 ICIS-1 Isdn InterfaceRemote Ports Isdn Interface RJ45 ConnectorCom Port 1.5 RJ45500-23-00 ICIS-2 Isdn Interface D15 Fixed Plug on ICIS-2 DTEGain Setting on Matrix CardsComputer Operating Systems Important Note Power SuppliesMatrix Download Installing AN Archipel Download Card in a P.C Commander Installation Guide Black BOX IC114A Pcmcia Serial Adaptor Card Matrix Ports D9 Legacy Control Panels Legacy Control Panel Facility Comparison Table2.1 500-3x-3x Series Standard Control Panel Rear View Test Port- D9 Fixed Socket Expansion Port- D9 Fixed Socket3 500-30 Series DIP Switch Settings Expansion Out- D9 Fixed Socket Connector Pin Out Expansion In D9 Fixed Socket4 500-40-0X Series Expansion Panels Commander Installation Guide Page D9 pin RJ 45 pin Colour see above Connecting VIA Structured CablingType B max length 10 metres D9 Free Plug Function Pin 6.1 500-39-30 Connector Pin Out 6 500-39-30 / 31 1U 12 KEY Panel with Loudspeaker8 500-43-51 1U, 8 REN Level Control Panel 6.2 500-39-30 Rear View7 500-3X-5X Series Control Panels Real Time Performance Matrix Audio Specification Using 500-06-02 Matrix CardsGeneral PanelsMiscellaneous I/O Card P.CCut Switch Action No action 10.1 500-3X-5X Series Internal Panel Switch Settings10.2 500-41 Desktop Panel Internal Settings Test Function 10.3 500-31-60 Programming CUT Switch OperationHSMic LSCut MCCut Off Loop Back Test Mode Safety PrecautionsMains Connector and Plug Transportation and Storage