Trilogy Touch Technology 9 manual 4.4 500-08-10 Changeover Card

Page 54

Commander Installation Guide

6.2.4.4500-08-10 Changeover Card

An additional adaptor cable must be fitted between the D9 on the mauve re-programming cable and the 10 pin Molex connector (J6) that is the connection point on the 500-08-10. Wiring details are given below.

10 way IDT Header (500-08-10)	D9 Free socket
1	1
2	6
3	2
4	7
5	3
6	8
7	4
8	9
9	5

Follow the instructions in section 6.2.4.1. Always ensure that the correct hardware type is selected in the drop down list box and the appropriate programming code is loaded.

6.3PROGRAMMING WITH THE 500-16-03 DOWNLOAD CONVERTER

For programming Commander cards and panels, the connector is 9 way male to female with the following connections. Note, not all pins are wired.

Commander Programming Cable

9 way D Male	9 way D Female
1 – Not used	1 – Not used
2	2
3	3
4	5
5	4
6 – Not used	6 – Not used
7 – Not used	7 – Not used
8	9
9	8

To program Commander cards you must set the changeover card (500-08-10) jumper J7 to left and issue a reset on both the TDM (500-01-10/11) and Talkback controller (500-02- 11/12) cards beforehand. For cards in the rack, this means pressing the relevant reset button.

Remember that the link cable from the unit to be programmed to the link

adapter must be present before issuing a reset.

Panels do not have a reset button and must be reset by briefly shorting pin 3 to pin 7 on the 9 way connector.

Page 54 of 81

Issue 9

Trilogy Communications Limited

Image 54

Contents Installation Guide Issue Date Reason for Change Approved Document Number50096601.doc Errata Sheet DescriptionContents Introduction Control Panels Legacy Hardware Options Available and Module Type Numbers Commander Installation Guide Issue Introduction UnpackingRack Mounting System Assembly 500-08-10 Changeover Module 1 500-08 Series Changeover CardCommander Installation Guide Commander Installation Guide 4 500-25-00 E1 Network Link Card 5 500-10 Series MISC. I/O GPI Cards6 500-06 Series Matrix Cards D9 Fixed Plug Pin Function Mains Connection and Fusing1 500-15-30 Series Power Supply XLR4 Fixed Socket Pin FunctionStarting the System Commander Installation Guide Connecting the Matrix Ports Connecting the PC to the Commander SystemConnection VIA a PC COM Port Using RS232 Connection VIA a 500-16-03 Download Converter BOX Sub D 9 free female Sub D 9 free maleSub D 9 free female Installing Pathfinder 574 not 576 for a six frame system Camera Connector Other Matrix ConnectionsMatrix Ports RJ-45 Alarms RS232 configurationRS422 configuration Serial Link RS232 / RS422Miscellaneous I/O Card Connector PIN-OUT Commander D37 Fixed Plug Pin DescriptionCommander D25 Fixed Socket Upper Connector Pins Description Commander D25 Fixed Socket Lower Connector Pins DescriptionCommander D9 Fixed Socket Pin Description 5.1 500-10 Switches and Indicators Suggested external wiring of Misc I/O card output 5.3 500-25 Network Card Indicators and Switches LEDConfiguring the Gain of Camera Inputs .5.1 Link Setting on Connecting Networked Systems 1 500-26 Network Rear Connector Unit RCUEither Serial Networking Commander Installation Guide Issue Current Range Control Panel Facility Comparison Table 500-41-XX Series Desktop Panels Specification RJ-45 Function Pin 2 500-3X-5X Series Standard Control Panel Rear ViewExpansion Port RJ45 socket Matrix and Expansion RJ45 socket view from rear of panelKeypad D9 Fixed Socket -51 variant only Gpio Local logic in and out D9 Fixed SocketAudio I/O D15 Fixed Socket View of Keypad front panel4 500-3X-5X Series DIP Switch Settings OFFRear Connector Layout Rear Connecor Layout Connections Expansion out RJ-45 fixed socket on panelMatrix RJ-45 fixed socket on panel Gpio Local logic in and out D9 Fixed Socket Keypad D9 Fixed Socket View of Keypad as seen on front panelControl Panel Gpio External Circuitry Rear Panel Layout Connector types500-31-60 Standard Facility 16 KEY Control Panel Headset 5 Pin XLR Fixed Socket front panelGpio Local logic in and out D9 Fixed Socket 10 500-33-00 / 500-45-00 / 500-46-00 Range Gpio Local logic in and out D9 Fixed Socket Commander Installation Guide Issue Ttprog Software 6.2.1 SET-UP Routine Starting the Programme Connecting the Hardware 4.2 500-02-1x Talkback Controller4.3 500-3x-3x Control Panels Commander Programming Cable Way D Male Way D Female 4.4 500-08-10 Changeover CardProgramming with the 500-16-03 Download Converter Beltpacks RM15TPD-12STelephone Interfaces Connector Detail per channelConnector Detail Trilogy 500-19-10 Telephone Interface FrameTelos ONE Alignment RT Equipment 500-22-00 ICIS-1 Isdn InterfaceRemote Ports Isdn Interface RJ45 ConnectorCom Port 1.5 RJ45500-23-00 ICIS-2 Isdn Interface D15 Fixed Plug on ICIS-2 DTEGain Setting on Matrix CardsPower Supplies Matrix DownloadComputer Operating Systems Important Note Installing AN Archipel Download Card in a P.C Commander Installation Guide Black BOX IC114A Pcmcia Serial Adaptor Card Matrix Ports D9 Legacy Control Panels Legacy Control Panel Facility Comparison Table2.1 500-3x-3x Series Standard Control Panel Rear View Test Port- D9 Fixed Socket Expansion Port- D9 Fixed Socket3 500-30 Series DIP Switch Settings Connector Pin Out Expansion In D9 Fixed Socket 4 500-40-0X Series Expansion PanelsExpansion Out- D9 Fixed Socket Commander Installation Guide Page Connecting VIA Structured Cabling Type B max length 10 metres D9 Free Plug Function PinD9 pin RJ 45 pin Colour see above 6.1 500-39-30 Connector Pin Out 6 500-39-30 / 31 1U 12 KEY Panel with Loudspeaker6.2 500-39-30 Rear View 7 500-3X-5X Series Control Panels8 500-43-51 1U, 8 REN Level Control Panel Real Time Performance Matrix Audio Specification Using 500-06-02 Matrix CardsGeneral PanelsMiscellaneous I/O Card P.C10.1 500-3X-5X Series Internal Panel Switch Settings 10.2 500-41 Desktop Panel Internal SettingsCut Switch Action No action 10.3 500-31-60 Programming CUT Switch Operation HSMic LSCut MCCut OffTest Function Loop Back Test Mode Safety PrecautionsMains Connector and Plug Transportation and Storage