Trilogy Touch Technology 9 Safety Precautions, Transportation and Storage, Removal of Covers

Page 81

Commander Installation Guide

11.500-16-03 DOWNLOAD CONVERTER SUPPLEMENTARY INFORMATION

11.1SAFETY PRECAUTIONS

This equipment has been designed and tested to the highest safety standards. The following precautions should be covered to ensure safe operation of the apparatus.

11.2TRANSPORTATION AND STORAGE

Careful inspection of the unit must be made after it has been subject to transportation or storage. Any serious damage which could render it dangerous must be acted upon to safeguard any potential user.

11.3MAINS CONNECTOR AND PLUG

The supply lead plug shall only be inserted into a supply socket equipped with an earth contact. Extension of the lead must include a suitable conductor for the protective earth.

This equipment must be earthed.

11.4FUSES

Only the specified value and type of fuse must be fitted in the event of a replacement.

The brown supply lead (live) is fitted with a series fuse located in the mains connector located on the rear panel and should the unit be fitted with a two pin plug then it is possible, if the supply is reversed, for parts of the equipment to remain at supply potential after the fuse has ruptured.

11.5REMOVAL OF COVERS

Care must be exercised if the covers of the unit are removed. All internal live parts are covered but the equipment should be disconnected from the supply source before repair or maintenance.

Should it be necessary to carry out adjustments with the supply voltage connected then this work must be done by suitably qualified personnel.

11.6BAUD RATE

The unit is set to work at 38400 as default, but can be configured to operate at 115200 baud. To change to this, the bottom link of J2 must be made (the link adapter must be de and re- powered).

You can tell the current operating baud rate of the link adapter by turning the unit off and back on. D3 will flash once for 38400 baud and twice for 115200 baud.

11.7LOOP BACK TEST MODE

To confirm that the PC end is working, link J2 top link and re-power the link adapter. The adapter will now echo any sent characters straight back. To use this, run up HyperTerminal configured for 38400 (or 115200), eight bit, 1 stop, no parity, hardware flow control. Disable local echo. Any characters typed should be echoed back to the screen.

Remember to unlink J2 when finished with the test.

Trilogy Communications Limited

Issue 9

Page 81 of 81

Image 81

Contents Installation Guide Issue Date Reason for Change Approved Document Number50096601.doc Description Errata SheetContents Introduction Control Panels Legacy Hardware Options Available and Module Type Numbers Commander Installation Guide Issue Introduction UnpackingRack Mounting System Assembly 1 500-08 Series Changeover Card 500-08-10 Changeover ModuleCommander Installation Guide Commander Installation Guide 5 500-10 Series MISC. I/O GPI Cards 4 500-25-00 E1 Network Link Card6 500-06 Series Matrix Cards 1 500-15-30 Series Power Supply Mains Connection and FusingD9 Fixed Plug Pin Function XLR4 Fixed Socket Pin FunctionStarting the System Commander Installation Guide Connecting the Matrix Ports Connecting the PC to the Commander SystemConnection VIA a PC COM Port Using RS232 Connection VIA a 500-16-03 Download Converter BOX Sub D 9 free female Sub D 9 free maleSub D 9 free female Installing Pathfinder 574 not 576 for a six frame system Camera Connector Other Matrix ConnectionsMatrix Ports RJ-45 RS422 configuration RS232 configurationAlarms Serial Link RS232 / RS422Commander D37 Fixed Plug Pin Description Miscellaneous I/O Card Connector PIN-OUTCommander D25 Fixed Socket Upper Connector Pins Description Commander D25 Fixed Socket Lower Connector Pins DescriptionCommander D9 Fixed Socket Pin Description 5.1 500-10 Switches and Indicators Suggested external wiring of Misc I/O card output LED 5.3 500-25 Network Card Indicators and SwitchesConfiguring the Gain of Camera Inputs .5.1 Link Setting on 1 500-26 Network Rear Connector Unit RCU Connecting Networked SystemsEither Serial Networking Commander Installation Guide Issue Current Range Control Panel Facility Comparison Table 500-41-XX Series Desktop Panels Specification Expansion Port RJ45 socket 2 500-3X-5X Series Standard Control Panel Rear ViewRJ-45 Function Pin Matrix and Expansion RJ45 socket view from rear of panelAudio I/O D15 Fixed Socket Gpio Local logic in and out D9 Fixed SocketKeypad D9 Fixed Socket -51 variant only View of Keypad front panelOFF 4 500-3X-5X Series DIP Switch SettingsRear Connector Layout Rear Connecor Layout Connections Expansion out RJ-45 fixed socket on panelMatrix RJ-45 fixed socket on panel Gpio Local logic in and out D9 Fixed Socket Keypad D9 Fixed Socket View of Keypad as seen on front panelControl Panel Gpio External Circuitry 500-31-60 Standard Facility 16 KEY Control Panel Connector typesRear Panel Layout Headset 5 Pin XLR Fixed Socket front panelGpio Local logic in and out D9 Fixed Socket 10 500-33-00 / 500-45-00 / 500-46-00 Range Gpio Local logic in and out D9 Fixed Socket Commander Installation Guide Issue Ttprog Software 6.2.1 SET-UP Routine Starting the Programme Connecting the Hardware 4.2 500-02-1x Talkback Controller4.3 500-3x-3x Control Panels Commander Programming Cable Way D Male Way D Female 4.4 500-08-10 Changeover CardProgramming with the 500-16-03 Download Converter RM15TPD-12S BeltpacksConnector Detail Connector Detail per channelTelephone Interfaces Trilogy 500-19-10 Telephone Interface FrameTelos ONE Alignment 500-22-00 ICIS-1 Isdn Interface RT EquipmentCom Port Isdn Interface RJ45 ConnectorRemote Ports 1.5 RJ45D15 Fixed Plug on ICIS-2 DTE 500-23-00 ICIS-2 Isdn InterfaceMatrix Cards Gain Setting onPower Supplies Matrix DownloadComputer Operating Systems Important Note Installing AN Archipel Download Card in a P.C Commander Installation Guide Black BOX IC114A Pcmcia Serial Adaptor Card Matrix Ports D9 Legacy Control Panel Facility Comparison Table Legacy Control Panels2.1 500-3x-3x Series Standard Control Panel Rear View Expansion Port- D9 Fixed Socket Test Port- D9 Fixed Socket3 500-30 Series DIP Switch Settings Connector Pin Out Expansion In D9 Fixed Socket 4 500-40-0X Series Expansion PanelsExpansion Out- D9 Fixed Socket Commander Installation Guide Page Connecting VIA Structured Cabling Type B max length 10 metres D9 Free Plug Function PinD9 pin RJ 45 pin Colour see above 6 500-39-30 / 31 1U 12 KEY Panel with Loudspeaker 6.1 500-39-30 Connector Pin Out6.2 500-39-30 Rear View 7 500-3X-5X Series Control Panels8 500-43-51 1U, 8 REN Level Control Panel General Matrix Audio Specification Using 500-06-02 Matrix CardsReal Time Performance Panels P.C Miscellaneous I/O Card10.1 500-3X-5X Series Internal Panel Switch Settings 10.2 500-41 Desktop Panel Internal SettingsCut Switch Action No action 10.3 500-31-60 Programming CUT Switch Operation HSMic LSCut MCCut OffTest Function Mains Connector and Plug Safety PrecautionsLoop Back Test Mode Transportation and Storage