Trilogy Touch Technology 9 manual Starting the System

Page 17

Commander Installation Guide

2.6STARTING THE SYSTEM

The system may now be powered and will load a configuration from the Flash RAM. The miniature rotary switch on the front edge of the 500-02 Talkback Controller selects the boot configuration bank. In a multi-frame system, this is the 500-02 Talkback Controller in Frame 1 of the matrix. It is not necessary to have the computer operating at this stage.

A few hints:

•Initially, do not fit the redundant (standby) controller modules.

•Remove any 500-10 Misc I/O cards and 500-25 Network Link cards temporarily. If they have not been included in the initial boot configuration (loaded from Flash RAM), the system will appear not to run, or will operate very slowly.

•Turn the flash bank selector switch “out of range” (e.g. position 5). The system will now start without loading a configuration from flash RAM.

•If the system is multi-frame, see Section 2.4.2 for further information about the Flash RAM selector switch.

•Normal operation of the 500-01-10 card is indicated by the alternating LED pattern shown below. The display rotary selector switch should be set to position 3.

This pattern is displayed when the Display Select Switch is set to position 3. Other patterns are described in the Commander Technical Manual.

Trilogy Communications Limited

Issue 9

Page 17 of 81

Image 17

Contents Installation Guide 50096601.doc Issue Date Reason for Change ApprovedDocument Number Description Errata SheetContents Introduction Control Panels Legacy Hardware Options Available and Module Type Numbers Commander Installation Guide Issue Rack Mounting IntroductionUnpacking System Assembly 1 500-08 Series Changeover Card 500-08-10 Changeover ModuleCommander Installation Guide Commander Installation Guide 5 500-10 Series MISC. I/O GPI Cards 4 500-25-00 E1 Network Link Card6 500-06 Series Matrix Cards 1 500-15-30 Series Power Supply Mains Connection and FusingD9 Fixed Plug Pin Function XLR4 Fixed Socket Pin FunctionStarting the System Commander Installation Guide Connection VIA a PC COM Port Using RS232 Connecting the Matrix PortsConnecting the PC to the Commander System Sub D 9 free female Connection VIA a 500-16-03 Download Converter BOXSub D 9 free female Sub D 9 free male Installing Pathfinder 574 not 576 for a six frame system Matrix Ports RJ-45 Camera ConnectorOther Matrix Connections RS422 configuration RS232 configurationAlarms Serial Link RS232 / RS422Commander D37 Fixed Plug Pin Description Miscellaneous I/O Card Connector PIN-OUTCommander D9 Fixed Socket Pin Description Commander D25 Fixed Socket Upper Connector Pins DescriptionCommander D25 Fixed Socket Lower Connector Pins Description 5.1 500-10 Switches and Indicators Suggested external wiring of Misc I/O card output LED 5.3 500-25 Network Card Indicators and SwitchesConfiguring the Gain of Camera Inputs .5.1 Link Setting on 1 500-26 Network Rear Connector Unit RCU Connecting Networked SystemsEither Serial Networking Commander Installation Guide Issue Current Range Control Panel Facility Comparison Table 500-41-XX Series Desktop Panels Specification Expansion Port RJ45 socket 2 500-3X-5X Series Standard Control Panel Rear ViewRJ-45 Function Pin Matrix and Expansion RJ45 socket view from rear of panelAudio I/O D15 Fixed Socket Gpio Local logic in and out D9 Fixed SocketKeypad D9 Fixed Socket -51 variant only View of Keypad front panelOFF 4 500-3X-5X Series DIP Switch SettingsRear Connector Layout Matrix RJ-45 fixed socket on panel Rear Connecor Layout ConnectionsExpansion out RJ-45 fixed socket on panel Gpio Local logic in and out D9 Fixed Socket Control Panel Gpio External Circuitry Keypad D9 Fixed SocketView of Keypad as seen on front panel 500-31-60 Standard Facility 16 KEY Control Panel Connector typesRear Panel Layout Headset 5 Pin XLR Fixed Socket front panelGpio Local logic in and out D9 Fixed Socket 10 500-33-00 / 500-45-00 / 500-46-00 Range Gpio Local logic in and out D9 Fixed Socket Commander Installation Guide Issue Ttprog Software 6.2.1 SET-UP Routine Starting the Programme 4.3 500-3x-3x Control Panels Connecting the Hardware4.2 500-02-1x Talkback Controller Programming with the 500-16-03 Download Converter Commander Programming Cable Way D Male Way D Female4.4 500-08-10 Changeover Card RM15TPD-12S BeltpacksConnector Detail Connector Detail per channelTelephone Interfaces Trilogy 500-19-10 Telephone Interface FrameTelos ONE Alignment 500-22-00 ICIS-1 Isdn Interface RT EquipmentCom Port Isdn Interface RJ45 ConnectorRemote Ports 1.5 RJ45D15 Fixed Plug on ICIS-2 DTE 500-23-00 ICIS-2 Isdn InterfaceMatrix Cards Gain Setting onComputer Operating Systems Important Note Power SuppliesMatrix Download Installing AN Archipel Download Card in a P.C Commander Installation Guide Black BOX IC114A Pcmcia Serial Adaptor Card Matrix Ports D9 Legacy Control Panel Facility Comparison Table Legacy Control Panels2.1 500-3x-3x Series Standard Control Panel Rear View Expansion Port- D9 Fixed Socket Test Port- D9 Fixed Socket3 500-30 Series DIP Switch Settings Expansion Out- D9 Fixed Socket Connector Pin Out Expansion In D9 Fixed Socket4 500-40-0X Series Expansion Panels Commander Installation Guide Page D9 pin RJ 45 pin Colour see above Connecting VIA Structured CablingType B max length 10 metres D9 Free Plug Function Pin 6 500-39-30 / 31 1U 12 KEY Panel with Loudspeaker 6.1 500-39-30 Connector Pin Out8 500-43-51 1U, 8 REN Level Control Panel 6.2 500-39-30 Rear View7 500-3X-5X Series Control Panels General Matrix Audio Specification Using 500-06-02 Matrix CardsReal Time Performance PanelsP.C Miscellaneous I/O CardCut Switch Action No action 10.1 500-3X-5X Series Internal Panel Switch Settings10.2 500-41 Desktop Panel Internal Settings Test Function 10.3 500-31-60 Programming CUT Switch OperationHSMic LSCut MCCut Off Mains Connector and Plug Safety PrecautionsLoop Back Test Mode Transportation and Storage