Trilogy Touch Technology 9 manual Telos ONE Alignment

Page 57

Commander Installation Guide

7.2.1TELOS ONE ALIGNMENT

The level adjustment of the Telos ONE hybrid unit is fairly critical. Slight variations can cause the unit to fail to initiate outgoing calls. The usual symptom will be failure to break the dial- tone when pressing keys on the dial-pad of a Trilogy panel. All units supplied via Trilogy are factory tested but this cannot take account of variations in local telephone lines and switchboards. To quickly re-align the levels, use the LED array on the front of the Telos unit.

To adjust the outgoing level:

¾Initiate an outgoing call from a control panel equipped with a dial-pad, such that dialling tone can be heard on the panel loudspeaker.

¾Press and hold a key on the dial pad, so that the DTMF tone is heard.

¾Select the in/out monitor switch on the Telos to “in”.

¾Adjust the multi-turn control labelled “Gain In” so that the 0 level LED is just illuminated. This is the last green LED: the red LED should not be lit.

To adjust the incoming level:

¾Call the Telos hybrid from another telephone line (e.g a mobile phone).and pick up the call.

¾Select the in/out monitor switch on the Telos to “out”.

¾While the line is active, press a key on the other telephone so that the DTMF tone is heard.

¾Adjust the multi-turn control labelled “Gain Out” so that the 0 level LED is just illuminated. This is the last green LED: the red LED should not be lit.

Trilogy recommends that these levels be checked from time to time, to ensure that the Telos hybrids remain correctly aligned.

NOTE: The Telos hybrid has an intelligent dimming circuit built into the unit, therefore we recommend that the port assigned to the telephone hybrid from the PathFinder GUI is set to 0dB dimming. Please refer to the PathFinder User Guide for more information.

Trilogy Communications Limited

Issue 9

Page 57 of 81

Image 57

Contents Installation Guide Issue Date Reason for Change Approved Document Number50096601.doc Description Errata SheetContents Introduction Control Panels Legacy Hardware Options Available and Module Type Numbers Commander Installation Guide Issue Introduction UnpackingRack Mounting System Assembly 1 500-08 Series Changeover Card 500-08-10 Changeover ModuleCommander Installation Guide Commander Installation Guide 5 500-10 Series MISC. I/O GPI Cards 4 500-25-00 E1 Network Link Card6 500-06 Series Matrix Cards 1 500-15-30 Series Power Supply Mains Connection and FusingD9 Fixed Plug Pin Function XLR4 Fixed Socket Pin FunctionStarting the System Commander Installation Guide Connecting the Matrix Ports Connecting the PC to the Commander SystemConnection VIA a PC COM Port Using RS232 Connection VIA a 500-16-03 Download Converter BOX Sub D 9 free female Sub D 9 free maleSub D 9 free female Installing Pathfinder 574 not 576 for a six frame system Camera Connector Other Matrix ConnectionsMatrix Ports RJ-45 RS422 configuration RS232 configurationAlarms Serial Link RS232 / RS422Commander D37 Fixed Plug Pin Description Miscellaneous I/O Card Connector PIN-OUTCommander D25 Fixed Socket Upper Connector Pins Description Commander D25 Fixed Socket Lower Connector Pins DescriptionCommander D9 Fixed Socket Pin Description 5.1 500-10 Switches and Indicators Suggested external wiring of Misc I/O card output LED 5.3 500-25 Network Card Indicators and SwitchesConfiguring the Gain of Camera Inputs .5.1 Link Setting on 1 500-26 Network Rear Connector Unit RCU Connecting Networked SystemsEither Serial Networking Commander Installation Guide Issue Current Range Control Panel Facility Comparison Table 500-41-XX Series Desktop Panels Specification Expansion Port RJ45 socket 2 500-3X-5X Series Standard Control Panel Rear ViewRJ-45 Function Pin Matrix and Expansion RJ45 socket view from rear of panelAudio I/O D15 Fixed Socket Gpio Local logic in and out D9 Fixed SocketKeypad D9 Fixed Socket -51 variant only View of Keypad front panelOFF 4 500-3X-5X Series DIP Switch SettingsRear Connector Layout Rear Connecor Layout Connections Expansion out RJ-45 fixed socket on panelMatrix RJ-45 fixed socket on panel Gpio Local logic in and out D9 Fixed Socket Keypad D9 Fixed Socket View of Keypad as seen on front panelControl Panel Gpio External Circuitry 500-31-60 Standard Facility 16 KEY Control Panel Connector typesRear Panel Layout Headset 5 Pin XLR Fixed Socket front panelGpio Local logic in and out D9 Fixed Socket 10 500-33-00 / 500-45-00 / 500-46-00 Range Gpio Local logic in and out D9 Fixed Socket Commander Installation Guide Issue Ttprog Software 6.2.1 SET-UP Routine Starting the Programme Connecting the Hardware 4.2 500-02-1x Talkback Controller4.3 500-3x-3x Control Panels Commander Programming Cable Way D Male Way D Female 4.4 500-08-10 Changeover CardProgramming with the 500-16-03 Download Converter RM15TPD-12S BeltpacksConnector Detail Connector Detail per channelTelephone Interfaces Trilogy 500-19-10 Telephone Interface FrameTelos ONE Alignment 500-22-00 ICIS-1 Isdn Interface RT EquipmentCom Port Isdn Interface RJ45 ConnectorRemote Ports 1.5 RJ45D15 Fixed Plug on ICIS-2 DTE 500-23-00 ICIS-2 Isdn InterfaceMatrix Cards Gain Setting onPower Supplies Matrix DownloadComputer Operating Systems Important Note Installing AN Archipel Download Card in a P.C Commander Installation Guide Black BOX IC114A Pcmcia Serial Adaptor Card Matrix Ports D9 Legacy Control Panel Facility Comparison Table Legacy Control Panels2.1 500-3x-3x Series Standard Control Panel Rear View Expansion Port- D9 Fixed Socket Test Port- D9 Fixed Socket3 500-30 Series DIP Switch Settings Connector Pin Out Expansion In D9 Fixed Socket 4 500-40-0X Series Expansion PanelsExpansion Out- D9 Fixed Socket Commander Installation Guide Page Connecting VIA Structured Cabling Type B max length 10 metres D9 Free Plug Function PinD9 pin RJ 45 pin Colour see above 6 500-39-30 / 31 1U 12 KEY Panel with Loudspeaker 6.1 500-39-30 Connector Pin Out6.2 500-39-30 Rear View 7 500-3X-5X Series Control Panels8 500-43-51 1U, 8 REN Level Control Panel General Matrix Audio Specification Using 500-06-02 Matrix CardsReal Time Performance PanelsP.C Miscellaneous I/O Card10.1 500-3X-5X Series Internal Panel Switch Settings 10.2 500-41 Desktop Panel Internal SettingsCut Switch Action No action 10.3 500-31-60 Programming CUT Switch Operation HSMic LSCut MCCut OffTest Function Mains Connector and Plug Safety PrecautionsLoop Back Test Mode Transportation and Storage