Trilogy Touch Technology 9 manual Connecting the Hardware, 4.2 500-02-1x Talkback Controller

Page 53

Commander Installation Guide

6.2.3CONNECTING THE HARDWARE

The instructions below assume that the PC is currently fitted with a suitable transputer link adaptor card and is in use for the PathFinder application.

•Close PathFinder

•Identify the download interconnection cable.

¾For desktop computers fitted with the Archipel link adaptor card, this will normally be a grey coloured D37 (PC) to D9 (Commander).

¾Disconnect the cable at both ends and replace with the violet coloured programming lead. Connect only at the computer.

¾For computers fitted with the Sundance SMT104 PCMCIA link adaptor, this will normally be a multi-part cable, with a D25 Male-Female “join”. Break this join.

¾Connect the violet D25-D9 cable instead.

•Move the “free” D9 connector to the front of the matrix. This may be connected directly to:-

¾500-01-10 TDM Controller

¾500-02-1x Talkback Controller

¾500-3x-3x and 500-4x Series Control Panels

An additional D9 –Molex adaptor is required to reprogram the 500-08-10 Changeover Card. See section 6.2.4.4.

6.2.4COMPLETING THE REPROGRAM SEQUENCE 6.2.4.1 500-01-10 TDM Controller

Carry out all the steps detailed in Sections 6.2.2 and 6.2.3. Now ensure that everyone is aware that the intercom system is about to go “off air”.

Connect the violet programming lead to the D9 connector on the front of the module. Halt the system by pressing the reset switch on the TDM controller.

On the PC, click the Program button. The progress bar indicates that the Flash RAM is being erased, then reprogrammed. A message box indicates that the procedure is complete.

If the frame is fitted with additional TDM controllers (either >96 ports or fault tolerant), then move the D9 to the next module and repeat the process.

When all modules have been reprogrammed, switch the power off, wait 10 seconds, then turn the power back on. Check that the system is running by observing the LED pattern on the TDM controllers.

6.2.4.2500-02-1x Talkback Controller

Follow the instructions in the preceding section. Always ensure that the correct hardware type is selected in the drop down list box and the appropriate programming code is loaded.

6.2.4.3500-3x-3x Control Panels

Control panels may be re-programmed without disruption to the matrix. Connect the violet programming lead to the rear connector labelled "Test/Debug”. After completing the programming sequence, re-start the panel by removing the mains power for a few seconds. Check that the panel re-initialises correctly by observing the LCD screen, which will display the current software version briefly. For panels without an alphanumeric display, check for correct operation.

Trilogy Communications Limited

Issue 9

Page 53 of 81

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Installation Guide 50096601.doc Issue Date Reason for Change ApprovedDocument Number Description Errata SheetContents Introduction Control Panels Legacy Hardware Options Available and Module Type Numbers Commander Installation Guide Issue Rack Mounting IntroductionUnpacking System Assembly 1 500-08 Series Changeover Card 500-08-10 Changeover ModuleCommander Installation Guide Commander Installation Guide 5 500-10 Series MISC. I/O GPI Cards 4 500-25-00 E1 Network Link Card6 500-06 Series Matrix Cards 1 500-15-30 Series Power Supply Mains Connection and FusingD9 Fixed Plug Pin Function XLR4 Fixed Socket Pin FunctionStarting the System Commander Installation Guide Connection VIA a PC COM Port Using RS232 Connecting the Matrix PortsConnecting the PC to the Commander System Sub D 9 free female Connection VIA a 500-16-03 Download Converter BOXSub D 9 free female Sub D 9 free male Installing Pathfinder 574 not 576 for a six frame system Matrix Ports RJ-45 Camera ConnectorOther Matrix Connections RS422 configuration RS232 configurationAlarms Serial Link RS232 / RS422Commander D37 Fixed Plug Pin Description Miscellaneous I/O Card Connector PIN-OUTCommander D9 Fixed Socket Pin Description Commander D25 Fixed Socket Upper Connector Pins DescriptionCommander D25 Fixed Socket Lower Connector Pins Description 5.1 500-10 Switches and Indicators Suggested external wiring of Misc I/O card output LED 5.3 500-25 Network Card Indicators and SwitchesConfiguring the Gain of Camera Inputs .5.1 Link Setting on 1 500-26 Network Rear Connector Unit RCU Connecting Networked SystemsEither Serial Networking Commander Installation Guide Issue Current Range Control Panel Facility Comparison Table 500-41-XX Series Desktop Panels Specification Expansion Port RJ45 socket 2 500-3X-5X Series Standard Control Panel Rear ViewRJ-45 Function Pin Matrix and Expansion RJ45 socket view from rear of panelAudio I/O D15 Fixed Socket Gpio Local logic in and out D9 Fixed SocketKeypad D9 Fixed Socket -51 variant only View of Keypad front panelOFF 4 500-3X-5X Series DIP Switch SettingsRear Connector Layout Matrix RJ-45 fixed socket on panel Rear Connecor Layout ConnectionsExpansion out RJ-45 fixed socket on panel Gpio Local logic in and out D9 Fixed Socket Control Panel Gpio External Circuitry Keypad D9 Fixed SocketView of Keypad as seen on front panel 500-31-60 Standard Facility 16 KEY Control Panel Connector typesRear Panel Layout Headset 5 Pin XLR Fixed Socket front panelGpio Local logic in and out D9 Fixed Socket 10 500-33-00 / 500-45-00 / 500-46-00 Range Gpio Local logic in and out D9 Fixed Socket Commander Installation Guide Issue Ttprog Software 6.2.1 SET-UP Routine Starting the Programme 4.3 500-3x-3x Control Panels Connecting the Hardware4.2 500-02-1x Talkback Controller Programming with the 500-16-03 Download Converter Commander Programming Cable Way D Male Way D Female4.4 500-08-10 Changeover Card RM15TPD-12S BeltpacksConnector Detail Connector Detail per channelTelephone Interfaces Trilogy 500-19-10 Telephone Interface FrameTelos ONE Alignment 500-22-00 ICIS-1 Isdn Interface RT EquipmentCom Port Isdn Interface RJ45 ConnectorRemote Ports 1.5 RJ45D15 Fixed Plug on ICIS-2 DTE 500-23-00 ICIS-2 Isdn InterfaceMatrix Cards Gain Setting onComputer Operating Systems Important Note Power SuppliesMatrix Download Installing AN Archipel Download Card in a P.C Commander Installation Guide Black BOX IC114A Pcmcia Serial Adaptor Card Matrix Ports D9 Legacy Control Panel Facility Comparison Table Legacy Control Panels2.1 500-3x-3x Series Standard Control Panel Rear View Expansion Port- D9 Fixed Socket Test Port- D9 Fixed Socket3 500-30 Series DIP Switch Settings Expansion Out- D9 Fixed Socket Connector Pin Out Expansion In D9 Fixed Socket4 500-40-0X Series Expansion Panels Commander Installation Guide Page D9 pin RJ 45 pin Colour see above Connecting VIA Structured CablingType B max length 10 metres D9 Free Plug Function Pin 6 500-39-30 / 31 1U 12 KEY Panel with Loudspeaker 6.1 500-39-30 Connector Pin Out8 500-43-51 1U, 8 REN Level Control Panel 6.2 500-39-30 Rear View7 500-3X-5X Series Control Panels General Matrix Audio Specification Using 500-06-02 Matrix CardsReal Time Performance PanelsP.C Miscellaneous I/O CardCut Switch Action No action 10.1 500-3X-5X Series Internal Panel Switch Settings10.2 500-41 Desktop Panel Internal Settings Test Function 10.3 500-31-60 Programming CUT Switch OperationHSMic LSCut MCCut Off Mains Connector and Plug Safety PrecautionsLoop Back Test Mode Transportation and Storage
Top Page Image Contents