Trilogy Touch Technology 9 Serial Link RS232 / RS422, RS232 configuration, RS422 configuration

Page 24

Commander Installation Guide

3.4.3SERIAL LINK (RS232 / RS422)

The current version of PC connector plate, which is fitted on the rear right hand side of the Commander Matrix frame, provides either RS232 or RS422 connection capability. The factory default setting is RS232: this may be changed by removing the 4 fixing screws, withdrawing the rear connector assembly and moving the PCB mounted jumper links to the alternate position. Most computers are fitted with D9 fixed sockets for the serial COM port. For older models equipped with a D25, suitable adaptors may be easily obtained.

RS232 configuration.

Commander Sub D9 Fixed Socket - Pin

Function

PC COM Port D9 Fixed Socket

1	DCD	1
2	TX	2
3	RX	3
4	DTR	4
5	0V or GND	5
6	DSR	6
7	CTS	7
8	RTS	8
9	n/c	9
Case

Note: Pin 1 through to Pin 8 MUST be wired 1:1. CAT 5 cable is suitable for most applications.

RS422 configuration.

Commander Sub D9
Fixed Socket Pin (+,-)	Function	Notes
4,8	422 in, +,-	Pair 1 (RX)
6,1	422 out, +,-	Pair 2 (TX)
7,2	422 RTS +,-	Pair 3
5,9	422 CTS +,-	Pair 4
3		Chassis

Connection to external equipment will depend on the manufacturer and model of RS422 card fitted. The table above only relates to the matrix.

3.4.4ALARMS

These are provided on a 9 way D type fixed socket on the rear of the matrix. The function of the output is software controlled from the 500-08-10 Changeover card. The output is a normally made, solid state relay contact. Maximum current rating is 120mA.

	Commander
	Commander
	D9 Fixed Socket - Pin	Function	Notes
	1,6	Right side OK	Pair 1
	2,7	Left side OK	Pair 2
	4,8	C/O Card OK	Pair 3
	5,9	Left side selected	Pair 4
	5,9	Left side selected	Pair 4
	3		Chassis

Page 24 of 81		Issue 9	Trilogy Communications Limited

Image 24

Contents Installation Guide Issue Date Reason for Change Approved Document Number50096601.doc Errata Sheet DescriptionContents Introduction Control Panels Legacy Hardware Options Available and Module Type Numbers Commander Installation Guide Issue Introduction UnpackingRack Mounting System Assembly 500-08-10 Changeover Module 1 500-08 Series Changeover CardCommander Installation Guide Commander Installation Guide 4 500-25-00 E1 Network Link Card 5 500-10 Series MISC. I/O GPI Cards6 500-06 Series Matrix Cards Mains Connection and Fusing 1 500-15-30 Series Power SupplyD9 Fixed Plug Pin Function XLR4 Fixed Socket Pin FunctionStarting the System Commander Installation Guide Connecting the Matrix Ports Connecting the PC to the Commander SystemConnection VIA a PC COM Port Using RS232 Connection VIA a 500-16-03 Download Converter BOX Sub D 9 free female Sub D 9 free maleSub D 9 free female Installing Pathfinder 574 not 576 for a six frame system Camera Connector Other Matrix ConnectionsMatrix Ports RJ-45 RS232 configuration RS422 configurationAlarms Serial Link RS232 / RS422Miscellaneous I/O Card Connector PIN-OUT Commander D37 Fixed Plug Pin DescriptionCommander D25 Fixed Socket Upper Connector Pins Description Commander D25 Fixed Socket Lower Connector Pins DescriptionCommander D9 Fixed Socket Pin Description 5.1 500-10 Switches and Indicators Suggested external wiring of Misc I/O card output 5.3 500-25 Network Card Indicators and Switches LEDConfiguring the Gain of Camera Inputs .5.1 Link Setting on Connecting Networked Systems 1 500-26 Network Rear Connector Unit RCUEither Serial Networking Commander Installation Guide Issue Current Range Control Panel Facility Comparison Table 500-41-XX Series Desktop Panels Specification 2 500-3X-5X Series Standard Control Panel Rear View Expansion Port RJ45 socketRJ-45 Function Pin Matrix and Expansion RJ45 socket view from rear of panelGpio Local logic in and out D9 Fixed Socket Audio I/O D15 Fixed SocketKeypad D9 Fixed Socket -51 variant only View of Keypad front panel4 500-3X-5X Series DIP Switch Settings OFFRear Connector Layout Rear Connecor Layout Connections Expansion out RJ-45 fixed socket on panelMatrix RJ-45 fixed socket on panel Gpio Local logic in and out D9 Fixed Socket Keypad D9 Fixed Socket View of Keypad as seen on front panelControl Panel Gpio External Circuitry Connector types 500-31-60 Standard Facility 16 KEY Control PanelRear Panel Layout Headset 5 Pin XLR Fixed Socket front panelGpio Local logic in and out D9 Fixed Socket 10 500-33-00 / 500-45-00 / 500-46-00 Range Gpio Local logic in and out D9 Fixed Socket Commander Installation Guide Issue Ttprog Software 6.2.1 SET-UP Routine Starting the Programme Connecting the Hardware 4.2 500-02-1x Talkback Controller4.3 500-3x-3x Control Panels Commander Programming Cable Way D Male Way D Female 4.4 500-08-10 Changeover CardProgramming with the 500-16-03 Download Converter Beltpacks RM15TPD-12SConnector Detail per channel Connector DetailTelephone Interfaces Trilogy 500-19-10 Telephone Interface FrameTelos ONE Alignment RT Equipment 500-22-00 ICIS-1 Isdn InterfaceIsdn Interface RJ45 Connector Com PortRemote Ports 1.5 RJ45500-23-00 ICIS-2 Isdn Interface D15 Fixed Plug on ICIS-2 DTEGain Setting on Matrix CardsPower Supplies Matrix DownloadComputer Operating Systems Important Note Installing AN Archipel Download Card in a P.C Commander Installation Guide Black BOX IC114A Pcmcia Serial Adaptor Card Matrix Ports D9 Legacy Control Panels Legacy Control Panel Facility Comparison Table2.1 500-3x-3x Series Standard Control Panel Rear View Test Port- D9 Fixed Socket Expansion Port- D9 Fixed Socket3 500-30 Series DIP Switch Settings Connector Pin Out Expansion In D9 Fixed Socket 4 500-40-0X Series Expansion PanelsExpansion Out- D9 Fixed Socket Commander Installation Guide Page Connecting VIA Structured Cabling Type B max length 10 metres D9 Free Plug Function PinD9 pin RJ 45 pin Colour see above 6.1 500-39-30 Connector Pin Out 6 500-39-30 / 31 1U 12 KEY Panel with Loudspeaker6.2 500-39-30 Rear View 7 500-3X-5X Series Control Panels8 500-43-51 1U, 8 REN Level Control Panel Matrix Audio Specification Using 500-06-02 Matrix Cards GeneralReal Time Performance PanelsMiscellaneous I/O Card P.C10.1 500-3X-5X Series Internal Panel Switch Settings 10.2 500-41 Desktop Panel Internal SettingsCut Switch Action No action 10.3 500-31-60 Programming CUT Switch Operation HSMic LSCut MCCut OffTest Function Safety Precautions Mains Connector and PlugLoop Back Test Mode Transportation and Storage