Trilogy Touch Technology 9 manual Matrix Cards, Gain Setting on

Page 61

Commander Installation Guide

8.LEGACY HARDWARE

The following hardware is no longer supplied by Trilogy Communications.

8.1MATRIX CARDS

•500-06-00 is marked 5510 on the card ejector since the base card is manufactured by Pro-Bel. It carries a Trilogy designed sub board.

•500-06-01 replaced the 500-06-00 and is a single board Trilogy design.

8.1.1GAIN SETTING ON 500-06-00

Ports intended for use with cameras will have the appropriate rear connector back fitted in the correct position, as per your requirements. The camera RCU has a passive-mixing pad fitted, which necessarily inserts a 25dB loss into the 6th port of the associated matrix card.

The 500-06-00 6 port interface module has a sub-module fitted on which are the analogue input and output buffers. The drawing below shows the layout of the 500-06-00 module, with its sub-module.

Note that the 500-06-00 module is based on a Pro-Bel module numbered 5510. The card ejector is marked with the number 5510, not 500-06-00.

On the sub-module are two links, which must be set correctly to provide gain compensation for the loss of the mixing pad. Two positions are provided - “NORM” and “CAMS”. One link must be moved to the CAMS position; the second link should be removed for operation with cameras.

Trilogy Communications Limited

Issue 9

Page 61 of 81

Image 61

Contents Installation Guide Document Number Issue Date Reason for Change Approved50096601.doc Description Errata SheetContents Introduction Control Panels Legacy Hardware Options Available and Module Type Numbers Commander Installation Guide Issue Unpacking IntroductionRack Mounting System Assembly 1 500-08 Series Changeover Card 500-08-10 Changeover ModuleCommander Installation Guide Commander Installation Guide 5 500-10 Series MISC. I/O GPI Cards 4 500-25-00 E1 Network Link Card6 500-06 Series Matrix Cards 1 500-15-30 Series Power Supply Mains Connection and FusingD9 Fixed Plug Pin Function XLR4 Fixed Socket Pin FunctionStarting the System Commander Installation Guide Connecting the PC to the Commander System Connecting the Matrix PortsConnection VIA a PC COM Port Using RS232 Sub D 9 free female Sub D 9 free male Connection VIA a 500-16-03 Download Converter BOXSub D 9 free female Installing Pathfinder 574 not 576 for a six frame system Other Matrix Connections Camera ConnectorMatrix Ports RJ-45 RS422 configuration RS232 configurationAlarms Serial Link RS232 / RS422Commander D37 Fixed Plug Pin Description Miscellaneous I/O Card Connector PIN-OUTCommander D25 Fixed Socket Lower Connector Pins Description Commander D25 Fixed Socket Upper Connector Pins DescriptionCommander D9 Fixed Socket Pin Description 5.1 500-10 Switches and Indicators Suggested external wiring of Misc I/O card output LED 5.3 500-25 Network Card Indicators and SwitchesConfiguring the Gain of Camera Inputs .5.1 Link Setting on 1 500-26 Network Rear Connector Unit RCU Connecting Networked SystemsEither Serial Networking Commander Installation Guide Issue Current Range Control Panel Facility Comparison Table 500-41-XX Series Desktop Panels Specification Expansion Port RJ45 socket 2 500-3X-5X Series Standard Control Panel Rear ViewRJ-45 Function Pin Matrix and Expansion RJ45 socket view from rear of panelAudio I/O D15 Fixed Socket Gpio Local logic in and out D9 Fixed SocketKeypad D9 Fixed Socket -51 variant only View of Keypad front panelOFF 4 500-3X-5X Series DIP Switch SettingsRear Connector Layout Expansion out RJ-45 fixed socket on panel Rear Connecor Layout ConnectionsMatrix RJ-45 fixed socket on panel Gpio Local logic in and out D9 Fixed Socket View of Keypad as seen on front panel Keypad D9 Fixed SocketControl Panel Gpio External Circuitry 500-31-60 Standard Facility 16 KEY Control Panel Connector typesRear Panel Layout Headset 5 Pin XLR Fixed Socket front panelGpio Local logic in and out D9 Fixed Socket 10 500-33-00 / 500-45-00 / 500-46-00 Range Gpio Local logic in and out D9 Fixed Socket Commander Installation Guide Issue Ttprog Software 6.2.1 SET-UP Routine Starting the Programme 4.2 500-02-1x Talkback Controller Connecting the Hardware4.3 500-3x-3x Control Panels 4.4 500-08-10 Changeover Card Commander Programming Cable Way D Male Way D FemaleProgramming with the 500-16-03 Download Converter RM15TPD-12S BeltpacksConnector Detail Connector Detail per channelTelephone Interfaces Trilogy 500-19-10 Telephone Interface FrameTelos ONE Alignment 500-22-00 ICIS-1 Isdn Interface RT EquipmentCom Port Isdn Interface RJ45 ConnectorRemote Ports 1.5 RJ45D15 Fixed Plug on ICIS-2 DTE 500-23-00 ICIS-2 Isdn InterfaceMatrix Cards Gain Setting onMatrix Download Power SuppliesComputer Operating Systems Important Note Installing AN Archipel Download Card in a P.C Commander Installation Guide Black BOX IC114A Pcmcia Serial Adaptor Card Matrix Ports D9 Legacy Control Panel Facility Comparison Table Legacy Control Panels2.1 500-3x-3x Series Standard Control Panel Rear View Expansion Port- D9 Fixed Socket Test Port- D9 Fixed Socket3 500-30 Series DIP Switch Settings 4 500-40-0X Series Expansion Panels Connector Pin Out Expansion In D9 Fixed SocketExpansion Out- D9 Fixed Socket Commander Installation Guide Page Type B max length 10 metres D9 Free Plug Function Pin Connecting VIA Structured CablingD9 pin RJ 45 pin Colour see above 6 500-39-30 / 31 1U 12 KEY Panel with Loudspeaker 6.1 500-39-30 Connector Pin Out7 500-3X-5X Series Control Panels 6.2 500-39-30 Rear View8 500-43-51 1U, 8 REN Level Control Panel General Matrix Audio Specification Using 500-06-02 Matrix CardsReal Time Performance PanelsP.C Miscellaneous I/O Card10.2 500-41 Desktop Panel Internal Settings 10.1 500-3X-5X Series Internal Panel Switch SettingsCut Switch Action No action HSMic LSCut MCCut Off 10.3 500-31-60 Programming CUT Switch OperationTest Function Mains Connector and Plug Safety PrecautionsLoop Back Test Mode Transportation and Storage