Trilogy Touch Technology Connection VIA a 500-16-03 Download Converter BOX, Sub D 9 free female

Page 20

Commander Installation Guide

3.2.2CONNECTION VIA A 500-16-03 DOWNLOAD CONVERTER BOX

A single frame (96 port) Commander system has two interfaces which may be used for downloading configuration data:

•Serial port (RS232/422)

•High speed (20MB/s) transputer port

With a standalone system, the RS232 connection is sufficient (see 3.2.1). In a multi-system environment, this serial port is required to pass networking information, and can no longer be used for configuration data. See section 4.2. Therefore, a 500-16-03 Converter should be used, between the PC serial port and the Commander high speed port.

Two connection cables are required.

The PC cable is a pin to pin 9 way cable with male connecting to the RS232 port on the Interface box and the female connecting to the PC Com port. For short cable runs of a few meters ribbon cable is acceptable, for longer runs please use screened CAT5 cable. Screen is connected to pin 3, cable pairs are 1/6, 2/7, 4/8, 5/9.

Sub D 9 free female	Sub D 9 free male
1	1
6	6
2	2
7	7
4	4
8	8
3	3
9	9
5 (screen)	5

The Link cable for Commander downloads is also a pin to pin 9 way cable, but with a female connector at both ends. For short cable runs of less than one meter ribbon cable is acceptable, for longer runs please use screened CAT5 cable. Screen is connected to pin 3, cable pairs are 1/6, 2/7, 4/8, 5/9.

Sub D 9 free female	Sub D 9 free female
1	1
6	6
2	2
7	7
4	4
8	8
5	5
9	9
3 (screen)	3

The 500-16-03 may also be used for flash reprogramming certain types of Commander hardware. See section 6.

Further information on the 500-16-03 is provided in section 11.

Page 20 of 81

Issue 9

Trilogy Communications Limited

Image 20

Contents Installation Guide 50096601.doc Issue Date Reason for Change ApprovedDocument Number Errata Sheet DescriptionContents Introduction Control Panels Legacy Hardware Options Available and Module Type Numbers Commander Installation Guide Issue Rack Mounting IntroductionUnpacking System Assembly 500-08-10 Changeover Module 1 500-08 Series Changeover CardCommander Installation Guide Commander Installation Guide 4 500-25-00 E1 Network Link Card 5 500-10 Series MISC. I/O GPI Cards6 500-06 Series Matrix Cards Mains Connection and Fusing 1 500-15-30 Series Power SupplyD9 Fixed Plug Pin Function XLR4 Fixed Socket Pin FunctionStarting the System Commander Installation Guide Connection VIA a PC COM Port Using RS232 Connecting the Matrix PortsConnecting the PC to the Commander System Sub D 9 free female Connection VIA a 500-16-03 Download Converter BOXSub D 9 free female Sub D 9 free male Installing Pathfinder 574 not 576 for a six frame system Matrix Ports RJ-45 Camera ConnectorOther Matrix Connections RS232 configuration RS422 configurationAlarms Serial Link RS232 / RS422Miscellaneous I/O Card Connector PIN-OUT Commander D37 Fixed Plug Pin DescriptionCommander D9 Fixed Socket Pin Description Commander D25 Fixed Socket Upper Connector Pins DescriptionCommander D25 Fixed Socket Lower Connector Pins Description 5.1 500-10 Switches and Indicators Suggested external wiring of Misc I/O card output 5.3 500-25 Network Card Indicators and Switches LEDConfiguring the Gain of Camera Inputs .5.1 Link Setting on Connecting Networked Systems 1 500-26 Network Rear Connector Unit RCUEither Serial Networking Commander Installation Guide Issue Current Range Control Panel Facility Comparison Table 500-41-XX Series Desktop Panels Specification 2 500-3X-5X Series Standard Control Panel Rear View Expansion Port RJ45 socketRJ-45 Function Pin Matrix and Expansion RJ45 socket view from rear of panelGpio Local logic in and out D9 Fixed Socket Audio I/O D15 Fixed SocketKeypad D9 Fixed Socket -51 variant only View of Keypad front panel4 500-3X-5X Series DIP Switch Settings OFFRear Connector Layout Matrix RJ-45 fixed socket on panel Rear Connecor Layout ConnectionsExpansion out RJ-45 fixed socket on panel Gpio Local logic in and out D9 Fixed Socket Control Panel Gpio External Circuitry Keypad D9 Fixed SocketView of Keypad as seen on front panel Connector types 500-31-60 Standard Facility 16 KEY Control PanelRear Panel Layout Headset 5 Pin XLR Fixed Socket front panelGpio Local logic in and out D9 Fixed Socket 10 500-33-00 / 500-45-00 / 500-46-00 Range Gpio Local logic in and out D9 Fixed Socket Commander Installation Guide Issue Ttprog Software 6.2.1 SET-UP Routine Starting the Programme 4.3 500-3x-3x Control Panels Connecting the Hardware4.2 500-02-1x Talkback Controller Programming with the 500-16-03 Download Converter Commander Programming Cable Way D Male Way D Female4.4 500-08-10 Changeover Card Beltpacks RM15TPD-12SConnector Detail per channel Connector DetailTelephone Interfaces Trilogy 500-19-10 Telephone Interface FrameTelos ONE Alignment RT Equipment 500-22-00 ICIS-1 Isdn InterfaceIsdn Interface RJ45 Connector Com PortRemote Ports 1.5 RJ45500-23-00 ICIS-2 Isdn Interface D15 Fixed Plug on ICIS-2 DTEGain Setting on Matrix CardsComputer Operating Systems Important Note Power SuppliesMatrix Download Installing AN Archipel Download Card in a P.C Commander Installation Guide Black BOX IC114A Pcmcia Serial Adaptor Card Matrix Ports D9 Legacy Control Panels Legacy Control Panel Facility Comparison Table2.1 500-3x-3x Series Standard Control Panel Rear View Test Port- D9 Fixed Socket Expansion Port- D9 Fixed Socket3 500-30 Series DIP Switch Settings Expansion Out- D9 Fixed Socket Connector Pin Out Expansion In D9 Fixed Socket4 500-40-0X Series Expansion Panels Commander Installation Guide Page D9 pin RJ 45 pin Colour see above Connecting VIA Structured CablingType B max length 10 metres D9 Free Plug Function Pin 6.1 500-39-30 Connector Pin Out 6 500-39-30 / 31 1U 12 KEY Panel with Loudspeaker8 500-43-51 1U, 8 REN Level Control Panel 6.2 500-39-30 Rear View7 500-3X-5X Series Control Panels Matrix Audio Specification Using 500-06-02 Matrix Cards GeneralReal Time Performance PanelsMiscellaneous I/O Card P.CCut Switch Action No action 10.1 500-3X-5X Series Internal Panel Switch Settings10.2 500-41 Desktop Panel Internal Settings Test Function 10.3 500-31-60 Programming CUT Switch OperationHSMic LSCut MCCut Off Safety Precautions Mains Connector and PlugLoop Back Test Mode Transportation and Storage