Trilogy Touch Technology 9 manual Mains Connection and Fusing, 1 500-15-30 Series Power Supply

Page 16

Commander Installation Guide

2.5MAINS CONNECTION AND FUSING

2.5.1500-15-30 SERIES POWER SUPPLY

The PSU chassis occupies an additional 2U of rack space below the matrix and is internally wired. The complete assembly therefore occupies 8U for a 96 port system, 14U for a 192 port system etc. The PSU is half rack width allowing two PSU modules to be fitted, thus providing backup operation.

Each power supply is fitted with a D9 socket, which provides a relay contact indicating the PSU status. The table below gives details. Connection should only be made to the pins indicated: any other connections may cause failure of the power supply unit. There is also an auxiliary power connector: details below.

D9 Fixed Plug Pin	Function
1	Relay normally closed
2	Relay normally open
3	Relay common

XLR4 Fixed Socket Pin	Function
1	0V
2	+15V
3	No connection
4	-15V

Note: The Aux power connector is protected by an internal self-resetting thermal fuse. Left and right (main and standby) supplies may be connected in parallel.

The power supplies are switched-mode units and will cope automatically with an input voltage of between 98 and 260 volts AC. This should be wired according to the instructions provided with your mating mains socket using suitable cable. See below for earthing details.

The mains plug has an integral fuse tray fitted with a 20mm glass cartridge slow blow/anti- surge fuse. The fuse rating is marked adjacent to each fuse tray.

2.5.2EARTHING REQUIREMENTS

The Trilogy 500-15-30 units are provided with a single 4mm-earthing stud on the rear panel. Incoming mains earth from the IEC connector is internally bonded to both the chassis and technical 0V to meet safety requirements and performance specifications. The stud allows the addition of an earth strap in rack installations.

Page 16 of 81

Issue 9

Trilogy Communications Limited

Image 16

Contents Installation Guide Document Number Issue Date Reason for Change Approved50096601.doc Errata Sheet DescriptionContents Introduction Control Panels Legacy Hardware Options Available and Module Type Numbers Commander Installation Guide Issue Unpacking IntroductionRack Mounting System Assembly 500-08-10 Changeover Module 1 500-08 Series Changeover CardCommander Installation Guide Commander Installation Guide 4 500-25-00 E1 Network Link Card 5 500-10 Series MISC. I/O GPI Cards6 500-06 Series Matrix Cards Mains Connection and Fusing 1 500-15-30 Series Power SupplyD9 Fixed Plug Pin Function XLR4 Fixed Socket Pin FunctionStarting the System Commander Installation Guide Connecting the PC to the Commander System Connecting the Matrix PortsConnection VIA a PC COM Port Using RS232 Sub D 9 free female Sub D 9 free male Connection VIA a 500-16-03 Download Converter BOXSub D 9 free female Installing Pathfinder 574 not 576 for a six frame system Other Matrix Connections Camera ConnectorMatrix Ports RJ-45 RS232 configuration RS422 configurationAlarms Serial Link RS232 / RS422Miscellaneous I/O Card Connector PIN-OUT Commander D37 Fixed Plug Pin DescriptionCommander D25 Fixed Socket Lower Connector Pins Description Commander D25 Fixed Socket Upper Connector Pins DescriptionCommander D9 Fixed Socket Pin Description 5.1 500-10 Switches and Indicators Suggested external wiring of Misc I/O card output 5.3 500-25 Network Card Indicators and Switches LEDConfiguring the Gain of Camera Inputs .5.1 Link Setting on Connecting Networked Systems 1 500-26 Network Rear Connector Unit RCUEither Serial Networking Commander Installation Guide Issue Current Range Control Panel Facility Comparison Table 500-41-XX Series Desktop Panels Specification 2 500-3X-5X Series Standard Control Panel Rear View Expansion Port RJ45 socketRJ-45 Function Pin Matrix and Expansion RJ45 socket view from rear of panelGpio Local logic in and out D9 Fixed Socket Audio I/O D15 Fixed SocketKeypad D9 Fixed Socket -51 variant only View of Keypad front panel4 500-3X-5X Series DIP Switch Settings OFFRear Connector Layout Expansion out RJ-45 fixed socket on panel Rear Connecor Layout ConnectionsMatrix RJ-45 fixed socket on panel Gpio Local logic in and out D9 Fixed Socket View of Keypad as seen on front panel Keypad D9 Fixed SocketControl Panel Gpio External Circuitry Connector types 500-31-60 Standard Facility 16 KEY Control PanelRear Panel Layout Headset 5 Pin XLR Fixed Socket front panelGpio Local logic in and out D9 Fixed Socket 10 500-33-00 / 500-45-00 / 500-46-00 Range Gpio Local logic in and out D9 Fixed Socket Commander Installation Guide Issue Ttprog Software 6.2.1 SET-UP Routine Starting the Programme 4.2 500-02-1x Talkback Controller Connecting the Hardware4.3 500-3x-3x Control Panels 4.4 500-08-10 Changeover Card Commander Programming Cable Way D Male Way D FemaleProgramming with the 500-16-03 Download Converter Beltpacks RM15TPD-12SConnector Detail per channel Connector DetailTelephone Interfaces Trilogy 500-19-10 Telephone Interface FrameTelos ONE Alignment RT Equipment 500-22-00 ICIS-1 Isdn InterfaceIsdn Interface RJ45 Connector Com PortRemote Ports 1.5 RJ45500-23-00 ICIS-2 Isdn Interface D15 Fixed Plug on ICIS-2 DTEGain Setting on Matrix CardsMatrix Download Power SuppliesComputer Operating Systems Important Note Installing AN Archipel Download Card in a P.C Commander Installation Guide Black BOX IC114A Pcmcia Serial Adaptor Card Matrix Ports D9 Legacy Control Panels Legacy Control Panel Facility Comparison Table2.1 500-3x-3x Series Standard Control Panel Rear View Test Port- D9 Fixed Socket Expansion Port- D9 Fixed Socket3 500-30 Series DIP Switch Settings 4 500-40-0X Series Expansion Panels Connector Pin Out Expansion In D9 Fixed SocketExpansion Out- D9 Fixed Socket Commander Installation Guide Page Type B max length 10 metres D9 Free Plug Function Pin Connecting VIA Structured CablingD9 pin RJ 45 pin Colour see above 6.1 500-39-30 Connector Pin Out 6 500-39-30 / 31 1U 12 KEY Panel with Loudspeaker7 500-3X-5X Series Control Panels 6.2 500-39-30 Rear View8 500-43-51 1U, 8 REN Level Control Panel Matrix Audio Specification Using 500-06-02 Matrix Cards GeneralReal Time Performance PanelsMiscellaneous I/O Card P.C10.2 500-41 Desktop Panel Internal Settings 10.1 500-3X-5X Series Internal Panel Switch SettingsCut Switch Action No action HSMic LSCut MCCut Off 10.3 500-31-60 Programming CUT Switch OperationTest Function Safety Precautions Mains Connector and PlugLoop Back Test Mode Transportation and Storage