Polycom 8020, 8030, 1725-36038-001 manual Network Config, IP Addresses

Page 30

SpectraLink 8020/8030 Wireless Telephone: Administration Guide for SIP

To optimize battery life, the interval between sending out ELP updates will vary based on handset state. It is expected that ELP updates will occur at most every two to six seconds and at least every few minutes. If improved tracking capability is desired, set the transmit interval for a shorter time between ELP updates. Increasing the frequency of transmissions will decrease battery life.

Location Server IP Allows the user to statically enter the IP address of the EPE. Enter the IP address and press NavOK to save.

Ekahau clients are not expected to find the EPE automatically.

Regardless of the handset’s selection of DHCP or static IP, the EPE

IP address must be statically entered in the Ekahau admin menus or

HAT.

ELP Port Allows the user to select the port number which ELP updates get sent to at the Location Server IP address. It must match the value configured in the Ekahau Positioning Engine for proper functionality. The ELP port number must be greater than zero and less than 65536.

Default is 8552. Enter the port number and press NavOK to save.

Network Config

IP Addresses

There are two modes in which the handset can operate: DHCP- enabled or Static IP. Select the mode for operation from the IP Address menu:

*Use DHCP Will use Dynamic Host Configuration Protocol to assign an IP Address each time the handset is turned on. If DHCP is enabled, the handset also receives all other IP Address configurations from the DHCP server.

Static IP Allows you to manually set a fixed IP Address. If selected, the handset will prompt for the IP addresses for each configurable network component. When entering addresses, enter the digits only, including leading zeroes. No periods are required.

Regardless of the mode in which the handset is operating, the following components are required and must be configured as part of the SIP system:

Phone IP The IP address of the handset. This is automatically assigned if DHCP is used. If using Static IP configuration, you

30

PN: 1725-36038-001_B.doc

Image 30
Contents Administration Guide Copyright Notice Trademark InformationPatent Information Contact InformationAbout this Guide Polycom Model NumbersRelated Documents Customer Support Hotline Icons and ConventionsContents Software Maintenance Using the SIP HandsetTesting a Handset Diagnostic Tools SIP Integration Factors101 IndexPage SpectraLink 8020/8030 Wireless Telephone Overview SpectraLink Voice Priority SVP Quality of ServiceSpectraLink 8020/8030 Wireless Telephone Security Quick Start GuideSpectraLink Wireless Telephone Overview System Diagram SpectraLink SVP ServerSystem Components SpectraLink 8020/8030 Wireless TelephoneAccess points SpectraLink 8000 SVP ServerEthernet switch SIP serverSIP phone Tftp server SIP Tftp serverSpectraLink 8020/8030 Wireless Telephone Specifications Table of Specifications Startup Sequence Icon Icons shown in bold turns off whenRegistering Standby mode on-hook Active mode off-hookHandset Modes Push-to-talk PTT mode Configuration menu modeMessaging mode Admin Menu Opening the Admin menuNavigation Toggle optionsData entry and editing Admin menu 4th level Admin Menu1st level 2nd level 3rd level 5th levelSS ID Network Config Reg. Domain Push-to-talk PTT Phone ConfigTelephony Protocol Time ZonePassword Enable/Disable/Change Daylight SavingsSIP Registration OAI Enable/Disable Location ServiceNetwork Config IP AddressesSpectraLink Wireless Telephone Configuration Ssid SecurityRotation Secret Regulatory Domain/802.11 Config/Transmit Power Enter the password that corresponds to this UsernameSubband Syslog Mode DiagnosticsDiagnostics Mode Error Handling ModeMenu option Setting Sub-option Restore DefaultsAdmin Menu Default Table Sub-sub-option DefaultDefault Sub-sub-optionConfig Menu User-Defined PreferencesMicrophone In-ear speaker Ring volume PTTDefault settings Setting/profile Silent Vibrate Soft Loud CustomPage Software License and Protocol Management RequirementsComponent Version Configuration Process Software License and Protocol Management Page SIP Integration Factors CODECsOption Meaning PN 1725-36038-001B.doc Programming the SIP Handset Features SIP Tftp Server Configuration FilesGuidelines Generic file sipallusers.cfg Handset-specific files e.g. sip3001.cfgProxy server commands Parameter Value DescriptionMailnotify Favorite Sample Configuration Files SIPallusers.cfg# PROXY1MAILACCESS = Sample handset-specific file #PROXY1ADDR #PROXY2ADDRLINE1 LINE1PROXY LINE1CALLID LINE2 Handset Display Using the SIP HandsetIndicator Function System iconsCall status icons State NavOK key function NavOK functionsSoftkeys Softkey Name Displayed during… Press to…Softkey Name Displayed during… Press to… Line menu Symbol menuMenus Key Number English Number + English PunctuationFavorites menu FCN menuHandset Operation If you want to… Then…If you want to… Then… Using the SIP Handset If you want to… Then… Using the SIP Handset Page Testing a Handset Page Diagnostic Tools Run Site Survey7 b c Solving coverage issues Diagnostics Enabled ScreenM m m Screen Syslog Mode Message type ErrorsEvents Full MAC Messages are formatted like the following example Page Certifying the Handsets Conducting a Site SurveyPN 1725-36038-001B.doc Normal Download Messages Software MaintenanceUpgrading Handsets Message DescriptionDownload Failure or Recovery Messages Situation during the download processRange/out-of-range TroubleshootingAccess Point Problems CapacityConfiguration Problems Transmission obstructionsHandset Status Messages Message Description ActionDhcp Troubleshooting Do not Power Dhcp Try Site Survey mode to determine a Message Description Action Maintenance Message Description Action Page Required? Peak power Domain Mode Band ChannelsMax. Power Limit Countries Appendix a Regulatory Domains100 Index OAI
Related manuals
Manual 48 pages 8.55 Kb