Panasonic KXTG9391T, KX-TG9391T Special instructions for programmable settings, Night mode, Alarm

Page 31

Programming

Special instructions for programmable settings

Night mode

Night mode allows you to select a span of time during which the unit will not ring for outside calls. This feature is useful for those occasions when you do not want to be disturbed, for example, while sleeping. Night mode can be set independently for each base unit and handset.

Important:

L Set the date and time beforehand (page 17).

LIf you have set the alarm, the alarm sounds even if the night mode is turned on.

Setting the start and end time

:Base unit / YHandset

1{MENU} i{#}{2}{3}{7}

2Enter the desired hour and minute you wish to start this feature.

3Press {*} to select “AM” or “PM”. i{OK}

4Enter the desired hour and minute you wish to end this feature.

5Press {*} to select “AM” or “PM”. i{OK}

6Proceed with the operation for your unit. Base unit: {■} (EXIT)

Handset: {OFF}

Note:

L To correct a digit:

Base unit: Press {7} or {8} to move the cursor to the digit, then make the correction. Handset: Press {<} or {>} to move the cursor to the digit, then make the correction.

Turning night mode on/off

:Base unit / YHandset

1{MENU} i{#}{2}{3}{8}

2{V}/{^}: Select “On” or “Off”. i{SAVE}

3Proceed with the operation for your unit. Base unit: {■} (EXIT)

Handset: {OFF}

Note:

L When the night mode is turned on, 3is displayed.

Alarm

An alarm sounds at the set time for 3 minutes once or daily. Alarm can be set for each handset.

Important:

L Set the date and time beforehand (page 17).

YHandset

1{MENU} i{#}{7}{2}{0}

2{V}/{^}: Select the desired alarm option. i

{SELECT}

Off

Turns alarm off. Go to step 5.

Once

An alarm sounds once at the set

 

time. Enter the desired month,

 

date, and year.

Daily

An alarm sounds daily at the set

 

time.

3Set the desired time. i{OK}

4{V}/{^}: Select the desired ringer tone. i

{SELECT}

L We recommend selecting a ringer tone different from the ringer tone set for outside calls.

5{V}/{^}: “Save” i{SELECT} i{OFF} L When the alarm is set, Eis displayed.

Note:

L To stop the alarm, press any dial key or place the handset on the charger.

L When the handset is in use, the alarm will not sound until the handset is in standby mode.

LIf you select “Once”, the setting changes to “Off” after the alarm sounds.

L The ringer volume for alarm follows the higher volume level of the 2 lines (page 29).

LWhen the ringer volume for outside calls of the 2 lines is set to off (page 29), the alarm sound is heard at a low level.

Customer support

The base unit and handset can display the Internet address where you can download the operating instructions or get further information for this product by using your computer.

:Base unit / YHandset

1{MENU} i{#}{6}{8}{0}

For assistance, please visit http://www.panasonic.com/help

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Model shown is KX-TG9391 Operating InstructionsTable of Contents KX-TG9391 series Product informationNotable differences between the models Thank you for purchasing a Panasonic digital cordless phoneSupplied accessories Accessory informationAdditional/replacement accessories Maximum of 5 parties are available System capabilitiesExpanding your phone system Sales and support informationFor your safety Environment Important safety instructionsFor best performance Base unit location/avoiding noiseDo not use benzine, thinner, or any abrasive powder Base unit ControlsHandset Using the navigator keys Display/IndicatorsSoft keys Select Symbols used in these operating instructionsLINE1 indicator/LINE2 indicator on the base unit Menu iconsCharger Connecting the AC adaptor/corded handsetDuring a power failure ConnectionsTo connect to 2 single-line telephone jacks Connecting the telephone line cordWire cord To connect to a 2-line telephone jackDSL/ADSL filter If you subscribe to a DSL/ADSL serviceExample DSL/ADSL line is line Transparent plug Jacks RJ11CBattery charge Battery installation and replacementVoice guidance language Setting up the unit before useDialing mode Display languageMenu i#250 Select the desired setting Line selection modeDate and time Making calls Answering calls Useful features during a call Call privacy Using the other line during a callThis feature allows you to join an existing outside call Call shareAdding entries Base unit/handset phonebookGroups Group Finding and calling a phonebook entryEditing entries Erasing entriesBase unit C Handset Menu iV/ Phonebook iSELECT Copying phonebook entriesCopying an entry Copying all entriesBase unit Main menu Sub-menu Programmable settingsProgramming by scrolling through the display menus Base unit / YHandset MenuHandset Main menu Sub-menu Main menu Sub-menuVoice prompt*1 Customer support Operating Feature Setting System Unit Code Programming using the direct commands280 To answer a call, turn off this feature237 Start/EndProgramming Customer support Special instructions for programmable settingsNight mode AlarmAdditional handsets Registering a unitOperating additional handsets Registering a handset to the base unitGroup ringer tone for phonebook Using Caller ID serviceCaller ID features Caller listHandset Call Caller ID number auto edit featureEditing a caller’s phone number before calling back Erasing selected caller informationErasing all caller information Turning the answering system on/off Answering systemGreeting message Listening to messages using the base unit Listening to messages using the handset Voice guidance Remote access codeUsing the answering system remotely Remote operationPlay greeting message Remote commandsTurning on the answering system remotely Skipping the greeting message to leave a messageTurning the call screening on/off Answering system settingsNumber of rings before the unit answers calls Caller’s recording timeVoice mail VM tone detection Voice mail serviceMenu i#332 Select the desired setting Voice Mail message indicationAnswering an intercom call IntercomTransferring calls Making an intercom callConference call with 2 outside calls Conference callsConference call with an outside call An intercom callAll registered handsets beep for 1 minute To stop paging Handset locatorYou can locate a misplaced handset by paging it Base unit LocatorTo attach the belt clip To remove the belt clip Wall mounting for chargerBelt clip Headset optionalDisplay message Cause/solution Error messagesGeneral use Problem Cause/solution TroubleshootingProgrammable settings Problem Cause/solution Making/answering calls, intercom Problem Cause/solution Battery recharge Problem Cause/solutionCaller ID Problem Cause/solution Answering system Problem Cause/solution Problem Cause/solutionTelephone line cord. Insert the batteries and charge fully You are entering the wrong remote access code. If youLiquid damage Problem Cause/solution Are completely dry, reconnect the AC adaptorFCC and other information FCC RF Exposure Warning Energy Star Specifications TTY users hearing or speech impaired users can call Customer servicesPanasonic Corporation WarrantyNorth America Limited Warranty Limits And Exclusions Index Additional handset Alarm 31 Answering calls Base unitPanasonic Puerto Rico, Inc When you ship the productPNQX1454ZA CM0708SY0 For your future reference
Top Page Image Contents