Uniden EXP1240 manual Configuring Level 1 Base Stations, Home/status screen primary base enabled

Page 33

EXP1240 System Installation Guide

Revision 06

7)If you want the base station to log low level multi cell debug information in the System Log, set the Multi cell debug field to Data Sync, Auto Tree, or Both. (This log contains a large number of messages, so you should leave it disabled most of the time.)

8)Click Save, then reboot the base station (go back to the Home/Status screen and click

Reboot).

9)When the base station finishes rebooting, verify that the RFPI-Addresson the Home/status screen shows RPN:00 at the end of the field. After a few minutes, the System Information field also updates to display the new status.

Figure 23: Home/status screen (primary base enabled)

Configuring Level 1 Base Stations

1)Place the first Level 1 base station at its final location.

2)Login to the base station.

3)Reset the base station to its default settings (open the Management screen and click Default Base Station). If this base station has never been configured, skip this step.

4)Go to the Multi-cellscreen and set the Multi cell system field to Enable.

5)Enter the System chain ID of the chain this base station should belong to.

6)If you want the base station to include low level multi cell debug information in the System Log, set the Multi cell debug field to Data Sync, Auto Tree, or Both. (This log contains a large number of messages, so you should leave it disabled most of the time.)

7)Click Save and reboot the base station (go back to the Home/Status screen and click

Reboot).

8)When the base station finishes rebooting, click Home, and after a few minutes, go back to the Multi-cellscreen. You will see that the System chain ID field is read-only, and the

DECT system settings and Base station settings fields, and the Base Station Group table are added to the bottom of the screen.

© 2013 Uniden America Corp.

PROPRIETARY AND CONFIDENTIAL

Page 33 of 71

Image 33
Contents Revision 06, July 7 EXP1240 SIP Dect System Installation GuideContents Appendix a Software Reference Table of Figures List of Tables Dect system settings parameters Check the Box Contents Important Safety InstructionsPurpose and Audience About This DocumentManual Conventions Terms used in this manualAbbreviations TermsBase Station Hardware SetupBase station LEDs and their meanings Connecting the base stationWall mounting the base station Base mounting dimensionsHandset front view Handset and ChargerPowering on the Handset Charging the batteryInitial System Configuration Summary Basic system configuration Using the Base Station InterfaceHome/Status screen Configuring General System SettingsManagement screen Change Configuration and Management SettingsChange the Pstn Tones and Emergency Dialing Change the Default PasswordCountry screen Configure the Network Settings ScreenTime Settings screen Configure Time SettingsChecking time settings updates Configuring the SIP Server SettingsSelecting YES indicates If information in rport and received Program the SIP Extensions To edit an existing serverTo delete a server Add Extension screen Register Handsets to Extensions To edit an extensionTo delete extensions Extensions screen, no handsets registered Extensions screen, three handsets registered To deregister a handsetIntroduction Timing LevelsSystem Chain ID and RPN Sample multi-cell system Setting Up a Multi-cell System Summary Multi-cell system configurationSample multi-cell system information Multi-cellscreen default values Configuring the Primary Base StationHome/status screen primary base enabled Configuring Level 1 Base StationsMulti-cellscreen top after configuration EXP1240 System Installation Guide Base Station Group table, Level 1 complete Multi-cellscreen Configuring Base Stations at Level 2 and UpBase Station Group table, Level 2 added Multi-cellscreen Removing Base Stations from a Multi-Cell SystemChanging the Primary Base Station in a Chain Multi cell Ready Keep-alive Primary Configuration screen Backing Up Configuration SettingsRestoring a Configuration Setting Up Firmware FoldersUpdating the Firmware Firmware path examples Configuring the Firmware Update SettingsUpdating Base Station Firmware Firmware Update screenUpdating Handsets Firmware update progress Extensions screen To verify the firmware updateAvailable Screens Base Station Configuration InterfaceGlobal Buttons and Options Home/Status Screen Read Only Home/Status OptionsHome/Status parameters Extensions options Extensions ScreenExtensions parameters read only Add Extension and Edit Extension screensParameter Description Extension Servers Screen Servers optionsServers parameters SIP server outbound proxy address. Use one of these formats Network Screen IP Settings parametersDhcp Options parameters Vlan Settings parametersSIP/RTP Settings parameters NAT Settings parametersManagement Screen Management Settings parametersSetting. The intended audience is Level 1 or 2 technical Firmware Update screen options Firmware Update ScreenUpdate Handsets parameters Time Screen Time Settings parametersDST Country Screen Web Security ScreenCentral Directory Screen Importing a new file will replace the existing contact list Multi Cell ScreenSettings for this unit parameters 71 for details RPN Dect Base Station Group parametersConfiguration Screen read only Syslog Screen read only SIP Log Screen read only Appendix B Rfpi Numbers