Uniden manual EXP1240 System Installation Guide

Page 35

EXP1240 System Installation Guide

Revision 06

The IP Status field of the base station you are logged into should show This unit. Any other base stations in this chain should show Connected (i.e., connected to the network and functioning properly) as their IP status. If any base station shows Connection Loss as its IP status, that base station is not connected to the network or has lost power.

The primary base station always serves as its own sync source, so the DECT sync source field should display Primary:RPN{its own RPN}. The DECT Property field shows Primary.

This base station's DECT sync source will show (any) RPN and its DECT Property field will show Locked.

Check the DECT sync source drop-down box for this base station to verify that there is a selection for the primary base station with a dBm value. If there is not a dBm value, wait for the system to further synchronize (approximately 2 minutes). When there is a dBm value, select the primary base station from the DECT sync source drop-down box and click Save.

If the primary base station is not on the list or if the signal strength is below - 70 to -73 dBm (-74dBm or less), move this base station to a different location. (You could also configure the other Level 1 base stations first and then come back and configure this one at Level 2.)

The DECT Chain appears at the bottom of the display and shows the synchronization source for all base stations in this system. Until the primary base station is selected as the DECT sync source, there will be a warning in the DECT Chain for this base station.

Figure 26: Base Station Group table, synchronization complete (Multi-cellscreen)

13)When the system has finished synchronizing, repeat this process for each base station at Level 1.

© 2013 Uniden America Corp.

PROPRIETARY AND CONFIDENTIAL

Page 35 of 71

Image 35
Contents Revision 06, July 7 EXP1240 SIP Dect System Installation GuideContents Appendix a Software Reference Table of Figures List of Tables Dect system settings parameters Check the Box Contents Important Safety InstructionsTerms used in this manual About This DocumentPurpose and Audience Manual ConventionsAbbreviations TermsBase Station Hardware SetupBase station LEDs and their meanings Connecting the base stationWall mounting the base station Base mounting dimensionsHandset front view Handset and ChargerPowering on the Handset Charging the batteryInitial System Configuration Summary Basic system configuration Using the Base Station InterfaceHome/Status screen Configuring General System SettingsManagement screen Change Configuration and Management SettingsChange the Pstn Tones and Emergency Dialing Change the Default PasswordCountry screen Configure the Network Settings ScreenTime Settings screen Configure Time SettingsChecking time settings updates Configuring the SIP Server SettingsSelecting YES indicates If information in rport and received To delete a server Program the SIP ExtensionsTo edit an existing server Add Extension screen To delete extensions Register Handsets to ExtensionsTo edit an extension Extensions screen, no handsets registered Extensions screen, three handsets registered To deregister a handsetSystem Chain ID and RPN IntroductionTiming Levels Sample multi-cell system Sample multi-cell system information Setting Up a Multi-cell SystemSummary Multi-cell system configuration Multi-cellscreen default values Configuring the Primary Base StationHome/status screen primary base enabled Configuring Level 1 Base StationsMulti-cellscreen top after configuration EXP1240 System Installation Guide Base Station Group table, Level 1 complete Multi-cellscreen Configuring Base Stations at Level 2 and UpBase Station Group table, Level 2 added Multi-cellscreen Removing Base Stations from a Multi-Cell SystemChanging the Primary Base Station in a Chain Multi cell Ready Keep-alive Primary Configuration screen Backing Up Configuration SettingsUpdating the Firmware Restoring a ConfigurationSetting Up Firmware Folders Firmware path examples Configuring the Firmware Update SettingsUpdating Base Station Firmware Firmware Update screenUpdating Handsets Firmware update progress Extensions screen To verify the firmware updateAvailable Screens Base Station Configuration InterfaceGlobal Buttons and Options Home/Status parameters Home/Status Screen Read OnlyHome/Status Options Extensions options Extensions ScreenExtensions parameters read only Add Extension and Edit Extension screensParameter Description Extension Servers parameters Servers ScreenServers options SIP server outbound proxy address. Use one of these formats Network Screen IP Settings parametersDhcp Options parameters Vlan Settings parametersSIP/RTP Settings parameters NAT Settings parametersManagement Screen Management Settings parametersSetting. The intended audience is Level 1 or 2 technical Firmware Update screen options Firmware Update ScreenUpdate Handsets parameters Time Screen Time Settings parametersDST Central Directory Screen Country ScreenWeb Security Screen Importing a new file will replace the existing contact list Multi Cell ScreenSettings for this unit parameters 71 for details RPN Dect Base Station Group parametersConfiguration Screen read only Syslog Screen read only SIP Log Screen read only Appendix B Rfpi Numbers