Uniden EXP1240 manual Network Screen, IP Settings parameters

Page 54

EXP1240 System Installation Guide

Revision 06

Network Screen

 

 

Table 15: IP Settings parameters

 

 

Parameter

Description

 

 

DHCP/Static IP

Select whether this base station gets its IP address from a DHCP server

or uses a static IP address.

 

 

 

IP Address

(static IP address only) Enter the 32-bit IP address this base station

should use.

 

 

 

 

 

 

(static IP address only) Enter the 32-bit mask to specify which part of

 

the IP address identifies the network (255) and which part identifies the

Subnet Mask

node (0). Class A, B, and C networks use the following default masks:

–

Class A: 255.0.0.0

 

 

–

Class B: 255.255.0.0

 

–

Class C: 255.255.255.0

 

 

 

© 2013 Uniden America Corp.

PROPRIETARY AND CONFIDENTIAL

Page 54 of 71

Page 53 Page 55
Image 54
Page 53 Page 55
Contents EXP1240 SIP Dect System Installation Guide Revision 06, July 7Contents Appendix a Software Reference Table of Figures List of Tables Dect system settings parameters Important Safety Instructions Check the Box ContentsManual Conventions About This DocumentPurpose and Audience Terms used in this manualTerms AbbreviationsHardware Setup Base StationConnecting the base station Base station LEDs and their meaningsBase mounting dimensions Wall mounting the base stationHandset and Charger Handset front viewCharging the battery Powering on the HandsetInitial System Configuration Using the Base Station Interface Summary Basic system configurationConfiguring General System Settings Home/Status screenChange Configuration and Management Settings Management screenChange the Default Password Change the Pstn Tones and Emergency DialingConfigure the Network Settings Screen Country screenConfigure Time Settings Time Settings screenConfiguring the SIP Server Settings Checking time settings updatesSelecting YES indicates If information in rport and received Program the SIP Extensions To edit an existing serverTo delete a server Add Extension screen Register Handsets to Extensions To edit an extensionTo delete extensions Extensions screen, no handsets registered To deregister a handset Extensions screen, three handsets registeredIntroduction Timing LevelsSystem Chain ID and RPN Sample multi-cell system Setting Up a Multi-cell System Summary Multi-cell system configurationSample multi-cell system information Configuring the Primary Base Station Multi-cellscreen default valuesConfiguring Level 1 Base Stations Home/status screen primary base enabledMulti-cellscreen top after configuration EXP1240 System Installation Guide Configuring Base Stations at Level 2 and Up Base Station Group table, Level 1 complete Multi-cellscreenRemoving Base Stations from a Multi-Cell System Base Station Group table, Level 2 added Multi-cellscreenChanging the Primary Base Station in a Chain Multi cell Ready Keep-alive Primary Backing Up Configuration Settings Configuration screenRestoring a Configuration Setting Up Firmware FoldersUpdating the Firmware Configuring the Firmware Update Settings Firmware path examplesFirmware Update screen Updating Base Station FirmwareUpdating Handsets To verify the firmware update Firmware update progress Extensions screenBase Station Configuration Interface Available ScreensGlobal Buttons and Options Home/Status Screen Read Only Home/Status OptionsHome/Status parameters Extensions Screen Extensions optionsAdd Extension and Edit Extension screens Extensions parameters read onlyParameter Description Extension Servers Screen Servers optionsServers parameters SIP server outbound proxy address. Use one of these formats IP Settings parameters Network ScreenVlan Settings parameters Dhcp Options parametersNAT Settings parameters SIP/RTP Settings parametersManagement Settings parameters Management ScreenSetting. The intended audience is Level 1 or 2 technical Firmware Update Screen Firmware Update screen optionsUpdate Handsets parameters Time Settings parameters Time ScreenDST Country Screen Web Security ScreenCentral Directory Screen Multi Cell Screen Importing a new file will replace the existing contact listSettings for this unit parameters 71 for details Base Station Group parameters RPN DectConfiguration Screen read only Syslog Screen read only SIP Log Screen read only Appendix B Rfpi Numbers
Top Page Image Contents