Uniden EXP1240 manual Updating Handsets

Page 44

EXP1240 System Installation Guide

Revision 06

8)Under the Update Base Stations section, select Update this BaseStation only to update only the base station you are currently connected to. To update all base stations at the same time, select Update all BaseStations.

9)Enter the last 3 digits of the firmware filename in the Required version field. The required version identifies the firmware file containing the update; for example, if you want to update the base station to the firmware file BeatusSW_4181_v0127.fwu, enter

127 in the Required version field.

10)Click Start update. When the base station asks you to confirm, click OK.

∘The base station firmware download will start. (You can check the download progress in the relevant log of your TFTP Server application.) The base station configuration interface will be temporarily unavailable when the base station(s) reboot at the end of the download. The overall update for a base station takes several minutes.

∘To verify the firmware update, go to the Home/Status screen and check the Firmware-Versionfield. The field shows the current firmware version in the format IPDECT/{Required FW version}/{date of FW file}, so in this example, the field should read IPDECT/01.27 followed by the date the file was created.

Updating Handsets

Updating handset firmware will take several hours and will affect the number of channels available for simultaneous call. Be sure to perform this update outside of normal business hours.

To finalize a firmware update, each handset must be placed in its charger. Be sure your end users return the handsets to the chargers before an update

Before starting an update, ensure that the TFTP Server is running.

•Each base station uses the DECT RF channels to download new firmware files to its handsets, and it can only update handsets that are registered to it.

•Each update session takes approximately 3 hours, and the base station will complete a session before starting a new one.

•A base station in a single cell system can update 10 handsets in a single session (because there are 10 available RF channels), so Handsets 1 through 10 are updated in session 1, Handsets 11 through 20 are updated in the second session, etc.

•In a multi-cell system, each base station can update 8 handsets in a session, but all base stations can perform update sessions at the same time. If you distribute the

© 2013 Uniden America Corp.

PROPRIETARY AND CONFIDENTIAL

Page 44 of 71

Page 43 Page 45
Image 44
Page 43 Page 45
Contents EXP1240 SIP Dect System Installation Guide Revision 06, July 7Contents Appendix a Software Reference Table of Figures List of Tables Dect system settings parameters Important Safety Instructions Check the Box ContentsAbout This Document Purpose and AudienceManual Conventions Terms used in this manualTerms AbbreviationsHardware Setup Base StationConnecting the base station Base station LEDs and their meaningsBase mounting dimensions Wall mounting the base stationHandset and Charger Handset front viewCharging the battery Powering on the HandsetInitial System Configuration Using the Base Station Interface Summary Basic system configurationConfiguring General System Settings Home/Status screenChange Configuration and Management Settings Management screenChange the Default Password Change the Pstn Tones and Emergency DialingConfigure the Network Settings Screen Country screenConfigure Time Settings Time Settings screenConfiguring the SIP Server Settings Checking time settings updatesSelecting YES indicates If information in rport and received To delete a server Program the SIP ExtensionsTo edit an existing server Add Extension screen To delete extensions Register Handsets to ExtensionsTo edit an extension Extensions screen, no handsets registered To deregister a handset Extensions screen, three handsets registeredSystem Chain ID and RPN IntroductionTiming Levels Sample multi-cell system Sample multi-cell system information Setting Up a Multi-cell SystemSummary Multi-cell system configuration Configuring the Primary Base Station Multi-cellscreen default valuesConfiguring Level 1 Base Stations Home/status screen primary base enabledMulti-cellscreen top after configuration EXP1240 System Installation Guide Configuring Base Stations at Level 2 and Up Base Station Group table, Level 1 complete Multi-cellscreenRemoving Base Stations from a Multi-Cell System Base Station Group table, Level 2 added Multi-cellscreenChanging the Primary Base Station in a Chain Multi cell Ready Keep-alive Primary Backing Up Configuration Settings Configuration screen Updating the Firmware Restoring a Configuration Setting Up Firmware Folders Configuring the Firmware Update Settings Firmware path examplesFirmware Update screen Updating Base Station FirmwareUpdating Handsets To verify the firmware update Firmware update progress Extensions screenBase Station Configuration Interface Available ScreensGlobal Buttons and Options Home/Status parameters Home/Status Screen Read OnlyHome/Status Options Extensions Screen Extensions optionsAdd Extension and Edit Extension screens Extensions parameters read onlyParameter Description Extension Servers parameters Servers ScreenServers options SIP server outbound proxy address. Use one of these formats IP Settings parameters Network ScreenVlan Settings parameters Dhcp Options parametersNAT Settings parameters SIP/RTP Settings parametersManagement Settings parameters Management ScreenSetting. The intended audience is Level 1 or 2 technical Firmware Update Screen Firmware Update screen optionsUpdate Handsets parameters Time Settings parameters Time ScreenDST Central Directory Screen Country ScreenWeb Security Screen Multi Cell Screen Importing a new file will replace the existing contact listSettings for this unit parameters 71 for details Base Station Group parameters RPN DectConfiguration Screen read only Syslog Screen read only SIP Log Screen read only Appendix B Rfpi Numbers
Top Page Image Contents