Dynaudio Air Series AIR Display, Overload Indication, Enter key Cursor UP/DOWN keys, Exit key

Page 19

THE AIR DISPLAY

EXIT

Overload Indication

ENTER

DOWN

ENTER key

CURSOR UP/DOWN keys

The ENTER key has two main functions:

These keys are used for navigating and adjusting

•

To enter the menus currently displayed.

parameter values.

•

To set the displayed parameter in Edit mode.

When a parameter can be edited via the CURSOR keys a

Overload Indication LED

“*” is set as the first character in front of the parameter.

When this LED flashes the monitors built-in amp is driven

beyond max performance. A continuos overload will

EXIT key

activate the amp protection circuit and the monitor will be

The EXIT key is used to exit the current display and go to

shut down. The monitor can be reactivated after a short

previous menu level.

period of cooling down.

This situation will NOT damage the monitor in any way.

Image 19

Contents Page Page Voltage Line plug according to standard Important Safety InstructionsPage Table of Contents Quick Setup Reference Quick Setup Reference Main Display Operational OverviewStereo Setup with stereo Subs SetupsStereo Setup Stereo Setup with mono SubsThis illustration shows how to connect a 5.1 analog setup Digital SetupAnalog Setup This illustration shows how to connect a 5.1 digital setupThis illustration shows how to connect a 5.3 Analog setup This illustration shows how to connect a 5.3 Digital setupDig/6 Master This illustration shows how to connect a 6.1 Analog setupAnalog connections Stereo Setup With Chains on L & ROther Chained Setups Analog/Digital setupDigital 192 kHz Digital Setup Product Concept Introduction This Manual BreakSlave & Sub Units Remote ControlCommon Features Master UnitOptional Digital I/O card Rear Panel Description MasterMaster Unit Analog I/O Slave/SubOverload Indication LED AIR DisplayOverload Indication Enter key Cursor UP/DOWN keysMain Display Press Enter to access the Select ModeParameter Description Basic operation in all menusExternal Clock Setup MenuSetup Set Monitor TaskRecall LFE channel noteStore Overview Placing the MonitorsOn the bridge / Console Close to wall / WallOther situations Evaluation Checking the placementPhase checking Checking by ear when listening to the signals In phaseNext EqualizingCurve Calibrating Main Monitors CurvesInterchannel calibration Acoustic level calibrationPlacing the Subwoofer Evaluation Low frequency sweepsChecking the Crosspoint Checking summing phase cancellationTo Calibrate Controlling standing wavesPolarity PhasePhase Introduction LFE GainGood acoustics AcousticsReverberation time Sabines formula Absorbtion or diffusion ? Resonance absorbers AbsorbersDiffusers Membrane absorbersStanding Waves Background Info AcousticsAxial Tangential Radial Room modesHow does the standing waves influence the sound field? How to prohibit standing wavesAcoustics Background Info Comb Filtering Dip frequencies Or +Rear wall cancellation Subwoofer Subwoofer Background InfoLow Pass LFE Gain Subwoofer & LFE Channel Background InfoLFE Channel Cross-oversAcoustic summation of audio signals Delaying Monitors LINE-UP & CalibrationCinema setup LINE-UP & Calibration Background Info How to measure the sound pressure?Calibration of 5.1 in an ITU-775 arrangement AIR Remote Remote Control FeaturesIntroduction Shift key Preset 1/3 and 2/4 keysVolume potentiometer REF Level 1-3 keysNavigating AIR Soft AIR SoftTools MainNetwork Preset ListSystem Setup Chained monitors Calibrate AIR-BaseLocal Parameters Reset ProceduresMiscellaneous Global ParametersSerial to Cat-5 cable CablesTC Link Standard Cat-5 cables AES/EBU Standard cablesAIR 20 & AIR 25 Master and Slave AIR 6 & AIR 15 Master and SlaveAIR Base AIR-Base-1 & AIR-Base-2General for all Products Room & DistanceAIR Remote specs Error messages etc Delay in System & Error Messages ETCCertificate Of Conformity Certificate of ConformityAIR AIR-Base # Name Preset List