Dynaudio Air Series manual Parameter Description, Basic operation in all menus, Main Display

Page 20

PARAMETER DESCRIPTION

Basic operation in all menus

Use ARROW keys to select value or submenu

Use ENTER to enter menus or for confirmation, and to activate

Use EXIT to step to a higher level or to decline an operation

Values are marked with an “ * “ when they can be altered via the ARROW keys

Main Display

The Main Display indicates the position of the monitor (when set up) and the set volume for the monitor.

A “+” indicates that this specific Master Unit has been set up to act as System Controller.

Bass Management

Bass management is possible in:

-Standard Stereo with 1 Sub

-Standard Stereo with 2 Subs

-5.1 Analog

-5.3 Analog

-6.1 Analog

-6.1 Digital - at 192kHz

-5.3 Digital

-5.1 Digital/6 Master

-5.1 Digital - at 192kHz

Satellite monitors uses 2nd order Hi Pass filters to attenuate frequencies below the set Cross-over frequency. Subs use 4th order Low Pass filter to attenuate frequencies above the set Cross-over frequency.

• Press ENTER to access the Select Mode

Off:

Bass Management is not activated. Only the LFE channel is distributed to the Sub.

AIR PC-IP

Via AIR PC-IP and advanced Bass Management mode is available. In this mode all filters (Satellite, Sub4 and Sub2) can be controlled to suit demanding setups.

Cross-over frequencies:

 

 

 

 

 

 

 

 

 

 

 

 

 

Menu Name

Satellite filter

 

 

 

Sub 4th order

 

Sub 2nd order

LFE = Sub

 

X-Over 50 Hz

 

50 Hz

 

50 Hz

 

50 Hz

 

No

 

 

 

X-Over 80 Hz

 

80 Hz

 

80Hz

 

80Hz

 

No

 

 

 

Extension 50 Hz

 

Off

 

50 Hz

 

50 Hz

 

No

 

 

 

Extension 80 Hz

 

Off

 

80 Hz

 

80 Hz

 

No

 

 

 

THX Sim 80 Hz

 

80 Hz

 

80 Hz

 

Off

 

Yes

 

 

 

Small Cons 120 Hz *

 

120 Hz

 

120 Hz

 

80Hz

 

Yes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note that the Extension 50 and 80Hz uses no Bass Management on satellite speaker thus playing full range. * Small Cons - Small Consumer

18

Image 20
Contents Page Page Important Safety Instructions Voltage Line plug according to standardPage Table of Contents Quick Setup Reference Quick Setup Reference Operational Overview Main DisplaySetups Stereo SetupStereo Setup with mono Subs Stereo Setup with stereo SubsDigital Setup Analog SetupThis illustration shows how to connect a 5.1 digital setup This illustration shows how to connect a 5.1 analog setupThis illustration shows how to connect a 5.3 Digital setup This illustration shows how to connect a 5.3 Analog setupThis illustration shows how to connect a 6.1 Analog setup Dig/6 MasterStereo Setup With Chains on L & R Other Chained SetupsAnalog/Digital setup Analog connectionsDigital 192 kHz Digital Setup Introduction This ManualBreak Product ConceptRemote Control Common FeaturesMaster Unit Slave & Sub UnitsRear Panel Description Master Master Unit Analog I/OSlave/Sub Optional Digital I/O cardAIR Display Overload IndicationEnter key Cursor UP/DOWN keys Overload Indication LEDPress Enter to access the Select Mode Parameter DescriptionBasic operation in all menus Main DisplaySetup Menu SetupSet Monitor Task External ClockStore LFE channel noteRecall Placing the Monitors OverviewOther situations Close to wall / WallOn the bridge / Console Checking the placement Phase checkingChecking by ear when listening to the signals In phase EvaluationEqualizing NextCalibrating Main Monitors Curves Interchannel calibrationAcoustic level calibration CurvePlacing the Subwoofer Low frequency sweeps EvaluationChecking summing phase cancellation To CalibrateControlling standing waves Checking the CrosspointPhase Phase IntroductionLFE Gain PolarityReverberation time AcousticsGood acoustics Sabines formula Absorbers DiffusersMembrane absorbers Absorbtion or diffusion ? Resonance absorbersBackground Info Acoustics Standing WavesRoom modes Axial Tangential RadialHow to prohibit standing waves How does the standing waves influence the sound field?Acoustics Background Info Comb Filtering Or + Dip frequenciesRear wall cancellation Subwoofer Background Info SubwooferSubwoofer & LFE Channel Background Info LFE ChannelCross-overs Low Pass LFE GainCinema setup Delaying Monitors LINE-UP & CalibrationAcoustic summation of audio signals Calibration of 5.1 in an ITU-775 arrangement How to measure the sound pressure?LINE-UP & Calibration Background Info Introduction Remote Control FeaturesAIR Remote Preset 1/3 and 2/4 keys Volume potentiometerREF Level 1-3 keys Shift keyAIR Soft Navigating AIR SoftMain ToolsPreset List NetworkSystem Setup Calibrate AIR-Base Chained monitorsReset Procedures MiscellaneousGlobal Parameters Local ParametersCables TC Link Standard Cat-5 cablesAES/EBU Standard cables Serial to Cat-5 cableAIR 6 & AIR 15 Master and Slave AIR 20 & AIR 25 Master and SlaveAIR-Base-1 & AIR-Base-2 AIR BaseAIR Remote specs Room & DistanceGeneral for all Products Delay in System & Error Messages ETC Error messages etcAIR AIR-Base Certificate of ConformityCertificate Of Conformity Preset List # Name