Dynaudio Air Series manual Cables, TC Link Standard Cat-5 cables, AES/EBU Standard cables

Page 54

CABLES

TC LINK Standard Cat-5 cables

Maximum Cable Length	:	15 meter.
Cable type	:	Shielded Ethernet Cable
		Category 5.
Connector type	:	RJ45

This connection is carrying Digital audio (24 bit) and network control information.

P1

P1		P2	Color
1		1	Brown

2		2	White/Brown

3		3	Green

4		4	White/Blue

5		5	Blue

6		6	White/Green

7		7	Orange

8		8	White/Orange

P2

AES/EBU Standard cables

Maximum Cable Length: 100 m

Cable type:	110 Ohm
Connector type:	XLR

XLR - XLR

Pin 1 - Pin 1 (Ground)

Pin 2 - Pin 2 (Hot)

Pin 3 - Pin 3 (Cold)

Serial to Cat-5 cable

-included with the AIR SOFT and AIR PC-IP. This is a proprietary cable with build in electronics for use with AIR Systems only !

USB to COM 9pin

-NOT included with AIR SOFT or AIR PC-IP. Use this type of converter in conjunction with the Cat5 to Serial cable described above if your computer has a USB connection only and no serial port.

52

Image 54

Contents Page Page Important Safety Instructions Voltage Line plug according to standardPage Table of Contents Quick Setup Reference Quick Setup Reference Operational Overview Main DisplayStereo Setup with mono Subs SetupsStereo Setup Stereo Setup with stereo SubsThis illustration shows how to connect a 5.1 digital setup Digital SetupAnalog Setup This illustration shows how to connect a 5.1 analog setupThis illustration shows how to connect a 5.3 Digital setup This illustration shows how to connect a 5.3 Analog setupThis illustration shows how to connect a 6.1 Analog setup Dig/6 MasterAnalog/Digital setup Stereo Setup With Chains on L & ROther Chained Setups Analog connectionsDigital 192 kHz Digital Setup Break IntroductionThis Manual Product ConceptMaster Unit Remote ControlCommon Features Slave & Sub UnitsSlave/Sub Rear Panel Description MasterMaster Unit Analog I/O Optional Digital I/O cardEnter key Cursor UP/DOWN keys AIR DisplayOverload Indication Overload Indication LEDBasic operation in all menus Press Enter to access the Select ModeParameter Description Main DisplaySet Monitor Task Setup MenuSetup External ClockLFE channel note RecallStore Placing the Monitors OverviewClose to wall / Wall On the bridge / ConsoleOther situations Checking by ear when listening to the signals In phase Checking the placementPhase checking EvaluationEqualizing NextAcoustic level calibration Calibrating Main Monitors CurvesInterchannel calibration CurvePlacing the Subwoofer Low frequency sweeps EvaluationControlling standing waves Checking summing phase cancellationTo Calibrate Checking the CrosspointLFE Gain PhasePhase Introduction PolarityAcoustics Good acousticsReverberation time Sabines formula Membrane absorbers AbsorbersDiffusers Absorbtion or diffusion ? Resonance absorbersBackground Info Acoustics Standing WavesRoom modes Axial Tangential RadialHow to prohibit standing waves How does the standing waves influence the sound field?Acoustics Background Info Comb Filtering Or + Dip frequenciesRear wall cancellation Subwoofer Background Info SubwooferCross-overs Subwoofer & LFE Channel Background InfoLFE Channel Low Pass LFE GainDelaying Monitors LINE-UP & Calibration Acoustic summation of audio signalsCinema setup How to measure the sound pressure? LINE-UP & Calibration Background InfoCalibration of 5.1 in an ITU-775 arrangement Remote Control Features AIR RemoteIntroduction REF Level 1-3 keys Preset 1/3 and 2/4 keysVolume potentiometer Shift keyAIR Soft Navigating AIR SoftMain ToolsPreset List NetworkSystem Setup Calibrate AIR-Base Chained monitorsGlobal Parameters Reset ProceduresMiscellaneous Local ParametersAES/EBU Standard cables CablesTC Link Standard Cat-5 cables Serial to Cat-5 cableAIR 6 & AIR 15 Master and Slave AIR 20 & AIR 25 Master and SlaveAIR-Base-1 & AIR-Base-2 AIR BaseRoom & Distance General for all ProductsAIR Remote specs Delay in System & Error Messages ETC Error messages etcCertificate of Conformity Certificate Of ConformityAIR AIR-Base Preset List # Name