Dynaudio Air Series manual Main, Tools

Page 49

AIR SOFT

Main

This is the Main screen from where all other AIR SOFT screens are accessed.

The (((•))) network icon (upper left corner)

If steady:

The computer running the AIR SOFT is not correctly connected to AIR monitors. Check connections, cables and refer to the setup-illustrations on pages 7-13 in this manual. If blinking:

The computer is correctly connected to your AIR monitor system.

The (((•))) icon is also used to access the Network screen. Press (((•))) to access.

VOLUME dialer

Use the mouse on the VOLUME dialer on the middle of the display to adjust Volume

REF LEV. keys

The three keys below the dialer instantly switches between the 3 user-defined Reference level settings.

To change these Ref. Levels:

Set dialer as desired

Hold cursor above Ref. Level key and select “Store” from the pop-up icons appearing.

Monitor and Sub icons

Depending on the currently selected setup (if any) satellite monitors and subs will be indicated by appropriate icons as illustrated above. Press to access specific parameters for the monitors.

This symbol in the Main screen indicates that the selected setup expects a monitor at a certain position but no monitor is found. Check your connections and retry.

Bass Mgt - Bass Management

Indicates the selected Cross-over frequency for Bass Management.

Tools

When placing the cursor on top of a monitor, a few tools will appear:

Press this symbol to enter calibration

pages

• Press to solo the monitor

• Press to mute the monitor

47

Image 49
Contents Page Page Voltage Line plug according to standard Important Safety InstructionsPage Table of Contents Quick Setup Reference Quick Setup Reference Main Display Operational OverviewStereo Setup SetupsStereo Setup with mono Subs Stereo Setup with stereo SubsAnalog Setup Digital SetupThis illustration shows how to connect a 5.1 digital setup This illustration shows how to connect a 5.1 analog setupThis illustration shows how to connect a 5.3 Analog setup This illustration shows how to connect a 5.3 Digital setupDig/6 Master This illustration shows how to connect a 6.1 Analog setupOther Chained Setups Stereo Setup With Chains on L & RAnalog/Digital setup Analog connectionsDigital 192 kHz Digital Setup This Manual IntroductionBreak Product ConceptCommon Features Remote ControlMaster Unit Slave & Sub UnitsMaster Unit Analog I/O Rear Panel Description MasterSlave/Sub Optional Digital I/O cardOverload Indication AIR DisplayEnter key Cursor UP/DOWN keys Overload Indication LEDParameter Description Press Enter to access the Select ModeBasic operation in all menus Main DisplaySetup Setup MenuSet Monitor Task External ClockRecall LFE channel noteStore Overview Placing the MonitorsOn the bridge / Console Close to wall / WallOther situations Phase checking Checking the placementChecking by ear when listening to the signals In phase EvaluationNext EqualizingInterchannel calibration Calibrating Main Monitors CurvesAcoustic level calibration CurvePlacing the Subwoofer Evaluation Low frequency sweepsTo Calibrate Checking summing phase cancellationControlling standing waves Checking the CrosspointPhase Introduction PhaseLFE Gain PolarityGood acoustics AcousticsReverberation time Sabines formula Diffusers AbsorbersMembrane absorbers Absorbtion or diffusion ? Resonance absorbersStanding Waves Background Info AcousticsAxial Tangential Radial Room modesHow does the standing waves influence the sound field? How to prohibit standing wavesAcoustics Background Info Comb Filtering Dip frequencies Or +Rear wall cancellation Subwoofer Subwoofer Background InfoLFE Channel Subwoofer & LFE Channel Background InfoCross-overs Low Pass LFE GainAcoustic summation of audio signals Delaying Monitors LINE-UP & CalibrationCinema setup LINE-UP & Calibration Background Info How to measure the sound pressure?Calibration of 5.1 in an ITU-775 arrangement AIR Remote Remote Control FeaturesIntroduction Volume potentiometer Preset 1/3 and 2/4 keysREF Level 1-3 keys Shift keyNavigating AIR Soft AIR SoftTools MainNetwork Preset ListSystem Setup Chained monitors Calibrate AIR-BaseMiscellaneous Reset ProceduresGlobal Parameters Local ParametersTC Link Standard Cat-5 cables CablesAES/EBU Standard cables Serial to Cat-5 cableAIR 20 & AIR 25 Master and Slave AIR 6 & AIR 15 Master and SlaveAIR Base AIR-Base-1 & AIR-Base-2General for all Products Room & DistanceAIR Remote specs Error messages etc Delay in System & Error Messages ETCCertificate Of Conformity Certificate of ConformityAIR AIR-Base # Name Preset List