Dynaudio Air Series Evaluation, Checking the placement, Low -frequency sweeps, Phase checking

Page 25

CHECKING - THE PLACEMENT OF THE MONITORS

Overview

1In the Setup menu: Select setup type (e.g. 5.1 or stereo) matching your application

2Check the phase (using the CD)

3Check the monitor positions (using the CD)

4Equalize the monitor (using the Bass and Treble parameters)

5Go to: Calibrate monitor

Select correction

In the main display select Recall preset now you can choose from a number of possibilities depending on the way the monitors are positioned in the room:

Room positions can be selected via the menu: Setup - Calibrate - Position

Neutral

Console

Wall

Console Wall

Corner

Console Corner

Select the one that matches your case.

Select Volume in the main menu to leave preset menu.

Set the volume: -10 dB

Test signals on CD. With the AIR monitors you received a CD containing a lot of useful test signals to be used for setting up of the monitors.

Checking the placement

When checking the placement of the monitors you first of all have to focus on the low frequencies. So the signals to be used are the low frequency sweeps as you find on the CD from track 31 to 39.

Low -frequency sweeps

The tracks 31 to 39 contains the following sweep sequences

Track 31: 200 Hz – 20 Hz

Track 32: 160 Hz – 20 Hz

Track 33: 125 Hz – 20 Hz

Track 34: 100 Hz – 20 Hz

Track 35: 80 Hz – 20 Hz

Track 36: 63 Hz – 20 Hz

Track 37: 50 Hz – 20 Hz

Track 38: 40 Hz – 20 Hz

During the sweeps you will hear short “bleebs” telling when the signal passes one of the ISO center frequencies. (See tables in appendix)

There are two “bleebs” every time the frequency passes a whole octave center frequency and one “bleeb” every time the in-between 1/3-octave center frequencies are passed. Play all the tracks using only one monitor at a time.

Evaluation

Phase checking

First procedure to be carried out is phase checking.

A number of signals both for two-channel stereo and for multi channel reproduction are provided with the CD.

Two channel stereo:

Use track 45-49. L/R signals are presented in phase and subsequently out of phase.

Multichannel:

Use the tracks 45-64 which contains DTS encoded signals pairwise comparable: L/R, L/C, L/LS, R/RS. If you do not have a DTS-decoder you may do the routing of the stereo L/R signals to other channels in your mixing console.

Checking by ear when listening to the signals: In phase:

You will hear more bass and the sound coming from a fixed point between the monitors.

Out of phase:

You will hear the sound image loose bass, the sound image is diffuse, and the directional information is blurred.

If you already have a phase checking measurement system that can be used as well.

In the listening position you should hear the signal smooth and even throughout all frequency sweeps (bearing in mind that the frequency response of the ear is not flat).

If you have a sound level meter this should be set to “LIN” with no frequency weighting. If the meter does not have a LIN position you can use the C-weighting, though the response is attenuated approximately 3 dB at 31.5 Hz and approximately 6 dB at 20 Hz.

In the background reading (page 43) you can find instructions on how alternatively to use a studio microphone if you do not have a sound level meter.

If OK; continue to next chapter: Calibrating the monitor setup. If not OK you must find new positions for the monitors.

You have to define at what frequency the response becomes bad. It is a frequency just above this you should select as the cross-over frequency between the main monitors and a subwoofer. If not possible to find any good positions for the main monitors or for the subwoofer you should consider changing the acoustics of the room. Equalization is a very common tool for the obtaining of a more smooth frequency response for steady state signals (like the sweeps). BUT remember: equalizing can never repair bad acoustics.

23

Image 25
Contents Page Page Voltage Line plug according to standard Important Safety InstructionsPage Table of Contents Quick Setup Reference Quick Setup Reference Main Display Operational OverviewStereo Setup SetupsStereo Setup with mono Subs Stereo Setup with stereo SubsAnalog Setup Digital SetupThis illustration shows how to connect a 5.1 digital setup This illustration shows how to connect a 5.1 analog setupThis illustration shows how to connect a 5.3 Analog setup This illustration shows how to connect a 5.3 Digital setupDig/6 Master This illustration shows how to connect a 6.1 Analog setupOther Chained Setups Stereo Setup With Chains on L & RAnalog/Digital setup Analog connectionsDigital 192 kHz Digital Setup This Manual IntroductionBreak Product ConceptCommon Features Remote ControlMaster Unit Slave & Sub UnitsMaster Unit Analog I/O Rear Panel Description MasterSlave/Sub Optional Digital I/O cardOverload Indication AIR DisplayEnter key Cursor UP/DOWN keys Overload Indication LEDParameter Description Press Enter to access the Select ModeBasic operation in all menus Main DisplaySetup Setup MenuSet Monitor Task External ClockRecall LFE channel noteStore Overview Placing the MonitorsOn the bridge / Console Close to wall / WallOther situations Phase checking Checking the placementChecking by ear when listening to the signals In phase EvaluationNext EqualizingInterchannel calibration Calibrating Main Monitors CurvesAcoustic level calibration CurvePlacing the Subwoofer Evaluation Low frequency sweepsTo Calibrate Checking summing phase cancellationControlling standing waves Checking the CrosspointPhase Introduction PhaseLFE Gain PolarityGood acoustics AcousticsReverberation time Sabines formula Diffusers AbsorbersMembrane absorbers Absorbtion or diffusion ? Resonance absorbersStanding Waves Background Info AcousticsAxial Tangential Radial Room modesHow does the standing waves influence the sound field? How to prohibit standing wavesAcoustics Background Info Comb Filtering Dip frequencies Or +Rear wall cancellation Subwoofer Subwoofer Background InfoLFE Channel Subwoofer & LFE Channel Background InfoCross-overs Low Pass LFE GainAcoustic summation of audio signals Delaying Monitors LINE-UP & CalibrationCinema setup LINE-UP & Calibration Background Info How to measure the sound pressure?Calibration of 5.1 in an ITU-775 arrangement AIR Remote Remote Control FeaturesIntroduction Volume potentiometer Preset 1/3 and 2/4 keysREF Level 1-3 keys Shift keyNavigating AIR Soft AIR SoftTools MainNetwork Preset ListSystem Setup Chained monitors Calibrate AIR-BaseMiscellaneous Reset ProceduresGlobal Parameters Local ParametersTC Link Standard Cat-5 cables CablesAES/EBU Standard cables Serial to Cat-5 cableAIR 20 & AIR 25 Master and Slave AIR 6 & AIR 15 Master and SlaveAIR Base AIR-Base-1 & AIR-Base-2General for all Products Room & DistanceAIR Remote specs Error messages etc Delay in System & Error Messages ETCCertificate Of Conformity Certificate of ConformityAIR AIR-Base # Name Preset List