Lincoln Electric SVM185-A Flow Meter, Operation on Lincnet Power Sources, Scfh, Liter/Min

Page 58

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

B-40

OPERATION

B-40

FLOW METER

The flowmeter shows the flow rate of shielding gas and has a valve to adjust the flow. The flow meter is scaled for CO2, Ar, and CO2/Ar blends. It is not calibrated and is for reference purposes only. The middle of the ball indicates the flow rate of shielding gas.

Adjust the flow rate while depressing the gas purge switch by turning the valve at the bottom of the meter. Most weld procedures require 25-40 scfh (11.8 - 18.9 lpm) for sufficient shielding gas coverage. Gun angle, nozzle diameter, joint configuration and wind condi- tions may effect the amount of shielding gas required.

 

 

 

 

SCFH

Liter/Min.

10

4.7

 

 

20

9.4

 

 

30

14.2

40

18.9

 

50

23.6

 

60

28.3

70

33.1

80

37.8

OPERATION ON LINCNET™ POWER

SOURCES

The POWER FEED® 25M is an ArcLink® wire feeder and is designed for operating on ArcLink® Power Wave® power sources. It is also capable of operating on older LincNet™ Power Wave® power sources though not all of the features will be active.

When operating with a LincNet™ power source,

Limits and Lock-outs are not available.

The weld mode description is not displayed when choosing weld modes.

When the weld mode is changed, any Arc Control values will remain as set for the previous weld mode.

Push-Pull guns will not function.

The IR port will not operate.

Error codes will by displayed as "ERR100". Error codes are deciphered by the flashing of the Status LED. (Counts of red flashes)

In the Set-Up menu, only parameters P.0 to P.99 are available.

POWER FEED® 25M

Image 58
Contents Power Feed 25M Safety Power Feed 25MElectric Shock can kill Fumes and GasesFor Electrically IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcElectromagnetic Compatibility EMC Safety Master Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications Power Feed 25M K2536-1Location Safety Precautions High Frequency ProtectionElectric Shock can Kill Digital Control CABLE, K1543-XX Power Source Wire FeederWiring FunctionCoaxial Weld Cable Weld Cable SizeTable A.1 Gtaw Electrode Polarity Shielding GAS ConnectionGmaw Build UP of Shielding GAS MAYChanging the Drive Motor Gear Ratio OFFWire Drive Configuration Procedure to Install Drive Rolls and Wire GuidesRemote Sense Lead Specifications Loading Spools of WireTypical System Configurations Table of Contents Operation Section Safety Precautions OperationDefinition of Welding Terms General DescriptionDuty Cycle Recommended Processes Recommended Power SourcesEquipment Limitations Pin connector Connector for a remote control11. ON/OFF switch Left Display windowTable B.1 ON-OFF SwitchStatus LED DefinitionMaking a Weld with Waveform Technology Power Sources7OPERATIONB-7 Smaw Stick WeldingSmaw Stick Welding Display Process Mode8OPERATIONB-8 MSP4 OperationWelding NON-SYNERGIC Gmaw and FcawThree non-synergic welding modes are available MSP4 Operation Non-Synergic Gmaw and Fcaw Welding Display Modes 5Gmaw MIG Synergic Welding Figure B.5220 26.4 Steel and Stainless Synergic GMAW-P Pulsed MIG Welding ARC ControlStainless Steel Gmaw Migwelding 220 Migand GMAW-PP Pulse on Pulse 16OPERATIONB-16Aluminum Synergic GMAW-P Pulsed Pulse-on-Pulse WeldingAluminum GMAW-P and GMAW-PP Aluminum Pulse WeldingAluminum GMAW-P and GMAW-PP Welding Figure B.14Aluminum Pulse and Pulse-On-Pulse Synergic Weld Display GMAW-STT Welding Figure B.15109 GMAW-STTTailout Figure B.16Touch Start Gtaw TIG WeldingTIG OFF 10M All Models SET-UP Features MenuPower Feed Feed 10AQuick Preflow time will not be accessible from the MSP4 Operation PROCEDURE/MEMORY Panel Opera User Memories Tion MSP4 Display LimitsParameter Range Units Limits may be set forLow Limit High LimitParameter Name Internal Controls Item D EscriptionHeater Switch Cold FEED/GAS Purge SwitchLight Switch Step Trigger OperationStrike 34OPERATIONPreflow WeldFigure B.20 Upslope Figure B.2137OPERATIONB-37 PostflowStart Figure B.23Description Rear ControlsScfh Operation on Lincnet Power SourcesFlow Meter Liter/MinTable of Contents Accessories Section Wire Type Electrode Size KP KIT AccessoriesFactory Installed Equipment Drive Roll Kits UsedK2593-xx #1 Co-Axial Power Cable Accessories K1500-5 Gun Receiver Bushing compatible Use a 5/16 nut driver to remove the screws holding InstallationCooling KIT Water cooling cover on the case front of the innerPython Water Cooled Guns Figure C.1Power Feed 25M Table of Contents Maintenance Section Periodic Maintenance MaintenanceRoutine Maintenance Calibration Specification1TABLE of CONTENTS-THEORY of Operation Section E-1 Theory of Operation Figure E.2 General Physical DescriptionPower Feed 25M Figure E.3 GAS Solenoid ControlsControl BOX User Interface Component Status Lights TroubleshootingComponent is causing the problem. By using the status Status Light StatesStatus Light States CON’T 1TABLE of Contents Troubleshooting and Repair F-1 2TROUBLESHOOTING and REPAIRF-2 HOW to USE Troubleshooting GuideTroubleshooting and Repair PC Board Troubleshooting ProceduresSee Setting DIP Switches Wire Drive Troubleshooting and Repair Output Problems Power Make certain the Power Wave Power source is functioningSetting Dip Switches in the Wire Troubleshooting and Repair ArcLink System Error Codes Fault Code Description Possible AdjustmentsPower Feed 25M Test Description Voltage Sense PC Board TestMaterials Needed Procedure Figure F.1 Plug J1 and J2 LocationsTach Feedback Test Blue RED Drive Motor Test #550 #551 Gear BOX and Drive Motor Removal and Replacement Procedure Figure F.4 Gear BOX and Drive Motor Removal and Replacement Gear BOX Removal and Drive MotorReplacement Procedures To Remove the Wire Drive Assembly from the Gear BOXTo Remove the Drive Motor from the Gear BOX SET UP Retest After RepairTable of Contents Diagram Section Electrical Diagrams Wiring Diagram Complete Machine Code 11313 G5585Schematic Complete Machine Code 11313 G5638 G5638Schematic 42 VAC & Arclink Feeder PC Board #1 G3883-2 Schematic 42 VAC & Arclink Feeder PC Board #2 G3883-2 Schematic MSP4 Optional Display PC Board G4456 Schematic SPI Display PC Board L11756 PC Board Assembly SPI Display L11757-1 Schematic Voltage Sense Select PC Board S24779 PC Board Assembly Voltage Sense Select M19540 Schematic Spool GUN PC Board L12008 PC Board Assembly Spool GUN M20159