Hitachi C 7BD2, C 7SB2 Blades and accessories must be securely mounted to the tool

Page 10

English

36.Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to youself or others. Blades, cutting implements and accessories which have been mounted to the tool should be secure and tight.

37.Never use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise appears defective, stop using it immediately and arrange for repairs by a Hitachi authorized service center.

38.Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may be deformed, cracked, or damaged.

39.Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dried thoroughly.

40.Never wear gloves made of material liable to roll up such as cotton, wool, cloth or string, etc.

41.Definitions for symbols V ............ volts

Hz .......... hertz

A ............ amperes

no .......... no load speed

.......... Class II Construction

---/min ... revolutions per minute

.......... alternating or direct current

10

Image 10
Contents Avertissement AdvertenciaTable DES Matieres ContentsÍndice Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Specific Safety Rules and Symbols Be careful of brake kickback. C7BD2 only DON’T TRY to Hold Short Places by Hand Never operate without all guards in place Keep motor air vent cleanOperate power tools at the rated voltage Use right toolNever use a tool which is defective or operating abnormally Blades and accessories must be securely mounted to the toolCarefully handle power tools Do not wipe plastic parts with solventMake Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationFunctional Description SpecificationsName of Parts Applications Assembly and OperationPrior to Operation Adjustsing the SAW Prior to USE Adjusting the angle of inclination Adjusting the cutting depth FigRegulating the guide Rip fence Cutting Procedures Pocket CuttingDismounting the saw blade Mounting and Dismounting the SAW BladeMounting the saw blade English Maintenance and Inspection Service parts list ModificationsPage Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTRègles Generale DE Sécurité SecuriteConserver CES Instructions Sécurité personnelle Règles DE Sécurité Spécifiques ET Symboles Français Faire attention au retour de freinage. C7BD2 seulement NE PAS Essayer DE Tenir LES Sections Courtes À LA Main Garder propres les Events d’air du moteur Utiliser l’outil motorisE a la tension nominaleManipuler l’outil motorisé avec précaution Ne pas essuyer les parties en plastique avec du solvantDouble Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES PartiesAvant L’UTILISATION Lunettes de protection Vérifier si les leviers a sont bien serrésVérifier le bon fonctionnement du carter de sécurité 10. Vérifier si la lame est serréeRéglage de la profondeur de coupe Fig Réglage DE LA Scie Avant L’UTILISATION AvertissementRéglage de l’angle d’inclinaison Procedures DE Coupe Avertissement Accessoire en optionMontage ET Demontage DE LA Lame DE Scie Démontage de la lameMontage de la lame Inspection de la lame de scie Remplacement dun balai en carboneEntretien ET Inspection Vérifier les visListe des pièces de rechange PrecaucionPage Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónGuarde Estas Instrucciones SeguridadNormas Generales DE Seguridad Seguridad eléctricaEspañol Normas Y Símbolos Específicos DE Seguridad Español Tenga cuidado con el contragolpe del freno ¡NO Intente Sujetar Partes Cortas CON LA Mano Maneje correctamente la herramienta No toque nunca las piezas móvilesUtilice la herramienta correcta Mantenga limpio el conducto de ventilación del motorNo limpie las partes de plástico con disolvente Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nomenclatura Descripción FunctionalEspecificaciones Aplicaciones Montaje Y OperaciónAntes DE LA Operación Ajuste DE LA Sierra Antes DE Utilizarla Regulación de la guía Guía de corte Ajuste de la profundidad de corte FigAjuste del ángulo de inclinación Si la palanca a estuviese floja, se podríanProcedimientos DE Corte Advertencia Montaje Y Desmontaje DE LA Cuchilla DE LA Sierra Advertencia Desmontaje de la cuchilla de la sierraMontaje de la cuchilla de la sierra Comprobación de los tornillos Mantenimiento E InspecciónInspección de la cuchilla de la sierra Inspección de la escobillas FigLista de repuestos ModificacionesPage Page Page Hitachi Koki Canada Co