Hitachi C 7SB2, C 7BD2 instruction manual Maintenance and Inspection

Page 19
Fig. 20

English

MAINTENANCE AND INSPECTION

WARNING: To avoid serious accident, ensure the switch is in the OFF position and disconnect the plug from the receptacle during maintenance and inspection.

1.Inspecting the saw blade:

Since use of a dull saw blade will degrade efficiency and cause possible motor malfunction, sharpen or replace the saw blade as soon as abrasion is noted.

CAUTION:

If a dull saw blade is used, reactive force is increased during cutting operation. Avoid the use of the dull saw blade without repair.

2.Check the screws

Loose screws are dangerous. Regularly inspect them and make sure they are tight.

CAUTION: Using this power tool with loosened screws is extremely dangerous.

3.Inspecting the carbon brushes (Fig. 20)

The motor employs carbon brushes which are consumable parts. Replace the carbon brush with a new one when it becomes worn to its wear limit. Always keep carbon brushes clean and ensure that they slide freely within the brush holders.

 

 

Wear limit

 

 

38

 

(6mm)

0.24"

No. of carbon

0.67"

 

 

 

 

brush

(17mm)

 

CAUTION:

Using this circular saw with a carbon brush which is worn in excess of the wear limit will damge the motor.

NOTE: Use HITACHI carbon brush No. 38 indicated in Fig. 20.

4. Replacing carbon brushes:

Remove the brush caps with a slotted-head screwdriver. The carbon brushes can then be easily removed. (Fig. 21)

5. Performance checkup and maintenance of

safety cover

 

Keep the safety cover in good shape for smooth

 

performance at all times. Be sure to make

 

prompt repair in case of any malfunction.

 

6. Adjusting the base and saw blade to

 

maintain perpendicularity

 

The angle between the base and the saw blade

Brush Cap Slotted-head

has been adjusted to 90°, however should this

Screwdriver

 

 

Fig. 21

19

Image 19
Contents Advertencia AvertissementTable DES Matieres ContentsÍndice Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Specific Safety Rules and Symbols Be careful of brake kickback. C7BD2 only DON’T TRY to Hold Short Places by Hand Use right tool Keep motor air vent cleanOperate power tools at the rated voltage Never operate without all guards in placeDo not wipe plastic parts with solvent Blades and accessories must be securely mounted to the toolCarefully handle power tools Never use a tool which is defective or operating abnormallyDouble Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolFunctional Description SpecificationsName of Parts Applications Assembly and OperationPrior to Operation Adjustsing the SAW Prior to USE Adjusting the angle of inclination Adjusting the cutting depth FigRegulating the guide Rip fence Pocket Cutting Cutting ProceduresDismounting the saw blade Mounting and Dismounting the SAW BladeMounting the saw blade English Maintenance and Inspection Modifications Service parts listPage Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéRègles Generale DE Sécurité SecuriteConserver CES Instructions Sécurité personnelle Règles DE Sécurité Spécifiques ET Symboles Français Faire attention au retour de freinage. C7BD2 seulement NE PAS Essayer DE Tenir LES Sections Courtes À LA Main Utiliser l’outil motorisE a la tension nominale Garder propres les Events d’air du moteurNe pas essuyer les parties en plastique avec du solvant Manipuler l’outil motorisé avec précautionDouble Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties Description FonctionnelleAvant L’UTILISATION 10. Vérifier si la lame est serrée Vérifier si les leviers a sont bien serrésVérifier le bon fonctionnement du carter de sécurité Lunettes de protectionRéglage de la profondeur de coupe Fig Réglage DE LA Scie Avant L’UTILISATION AvertissementRéglage de l’angle d’inclinaison Accessoire en option Procedures DE Coupe AvertissementDémontage de la lame Montage ET Demontage DE LA Lame DE ScieMontage de la lame Vérifier les vis Remplacement dun balai en carboneEntretien ET Inspection Inspection de la lame de sciePrecaucion Liste des pièces de rechangePage Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadSeguridad eléctrica SeguridadNormas Generales DE Seguridad Guarde Estas InstruccionesEspañol Normas Y Símbolos Específicos DE Seguridad Español Tenga cuidado con el contragolpe del freno ¡NO Intente Sujetar Partes Cortas CON LA Mano Mantenga limpio el conducto de ventilación del motor No toque nunca las piezas móvilesUtilice la herramienta correcta Maneje correctamente la herramientaNo limpie las partes de plástico con disolvente Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nomenclatura Descripción FunctionalEspecificaciones Aplicaciones Montaje Y OperaciónAntes DE LA Operación Ajuste DE LA Sierra Antes DE Utilizarla Si la palanca a estuviese floja, se podrían Ajuste de la profundidad de corte FigAjuste del ángulo de inclinación Regulación de la guía Guía de corteProcedimientos DE Corte Advertencia Desmontaje de la cuchilla de la sierra Montaje Y Desmontaje DE LA Cuchilla DE LA Sierra AdvertenciaMontaje de la cuchilla de la sierra Inspección de la escobillas Fig Mantenimiento E InspecciónInspección de la cuchilla de la sierra Comprobación de los tornillosModificaciones Lista de repuestosPage Page Page Hitachi Koki Canada Co