Hitachi C 7BD2, C 7SB2 instruction manual General Safety Rules

Page 4

English

SAFETY

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1.Work Area

(1)Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

(2)Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust of fumes.

(3)Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

2.Electrical Safety

(1)Double Insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double

Insulation eliminates the need for the three wire grounded power cord and grounded power supply system.

(2)Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

(3)Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

(4)Do not abuse the cord. Never use the cord to carry the tools or pull the plug from a receptacle. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

(5)When operating a power tool outside, use an outdoor extension cord marked “W- A” or “W”. These cords are rated for outdoor use and reduce the risk of electric shock.

3.Personal Safety

(1)Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

4

Image 4

Contents Avertissement AdvertenciaTable DES Matieres ContentsÍndice Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Specific Safety Rules and Symbols Be careful of brake kickback. C7BD2 only DON’T TRY to Hold Short Places by Hand Keep motor air vent clean Operate power tools at the rated voltageNever operate without all guards in place Use right toolBlades and accessories must be securely mounted to the tool Carefully handle power toolsNever use a tool which is defective or operating abnormally Do not wipe plastic parts with solventMake Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationFunctional Description SpecificationsName of Parts Applications Assembly and OperationPrior to Operation Adjustsing the SAW Prior to USE Adjusting the angle of inclination Adjusting the cutting depth FigRegulating the guide Rip fence Cutting Procedures Pocket CuttingDismounting the saw blade Mounting and Dismounting the SAW BladeMounting the saw blade English Maintenance and Inspection Service parts list ModificationsPage Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTRègles Generale DE Sécurité SecuriteConserver CES Instructions Sécurité personnelle Règles DE Sécurité Spécifiques ET Symboles Français Faire attention au retour de freinage. C7BD2 seulement NE PAS Essayer DE Tenir LES Sections Courtes À LA Main Garder propres les Events d’air du moteur Utiliser l’outil motorisE a la tension nominaleManipuler l’outil motorisé avec précaution Ne pas essuyer les parties en plastique avec du solvantDouble Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES PartiesAvant L’UTILISATION Vérifier si les leviers a sont bien serrés Vérifier le bon fonctionnement du carter de sécuritéLunettes de protection 10. Vérifier si la lame est serréeRéglage de la profondeur de coupe Fig Réglage DE LA Scie Avant L’UTILISATION AvertissementRéglage de l’angle d’inclinaison Procedures DE Coupe Avertissement Accessoire en optionMontage ET Demontage DE LA Lame DE Scie Démontage de la lameMontage de la lame Remplacement dun balai en carbone Entretien ET InspectionInspection de la lame de scie Vérifier les visListe des pièces de rechange PrecaucionPage Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónSeguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Seguridad eléctricaEspañol Normas Y Símbolos Específicos DE Seguridad Español Tenga cuidado con el contragolpe del freno ¡NO Intente Sujetar Partes Cortas CON LA Mano No toque nunca las piezas móviles Utilice la herramienta correctaManeje correctamente la herramienta Mantenga limpio el conducto de ventilación del motorNo limpie las partes de plástico con disolvente Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nomenclatura Descripción FunctionalEspecificaciones Aplicaciones Montaje Y OperaciónAntes DE LA Operación Ajuste DE LA Sierra Antes DE Utilizarla Ajuste de la profundidad de corte Fig Ajuste del ángulo de inclinaciónRegulación de la guía Guía de corte Si la palanca a estuviese floja, se podríanProcedimientos DE Corte Advertencia Montaje Y Desmontaje DE LA Cuchilla DE LA Sierra Advertencia Desmontaje de la cuchilla de la sierraMontaje de la cuchilla de la sierra Mantenimiento E Inspección Inspección de la cuchilla de la sierraComprobación de los tornillos Inspección de la escobillas FigLista de repuestos ModificacionesPage Page Page Hitachi Koki Canada Co