Hitachi C 7SB2, C 7BD2 Mounting and Dismounting the SAW Blade, Dismounting the saw blade

Page 17

English

5.Release the lever. When the lower guard contacts the work piece surface, it will be in proper position to open freely when cutting is commencend.

6.Holding the saw in position, with the blade not contacting the work piece surface, pull the trigger.

7.After the saw has reached full speed, gradually lower rear end of the saw until its base rests on the work surface.

8.Advance saw along the cutting line up to the corner.

9.Release trigger and allow blade to stop completely before withdrawing the blade from the work piece.

○Never under any circumstances pull the saw backwards while the blade is in motion, as

kickback may result.

10.Use a jig saw or hand saw to cut the corners out clean.

11.When starting each new cut, repeat as above.

MOUNTING AND DISMOUNTING THE SAW BLADE

WARNING: To avoid serious accident ensure the switch is in the OFF position, and disconnect the plug from the receptacle.

1.Dismounting the saw blade

(1)Set the cutting volume at maximum, and place the Circular Saw as shown in Fig. 17.

(2)Depress the lock lever, lock the spindle, and remove the hexagonal-flange bolt and washer(B) with the wrench.

(3)While holding the lever to keep the lower guard fully retracted into the blade cover, remove the saw blade. (Fig. 18)

2.Mounting the saw blade

(1)Thoroughly remove any sawdust which has accumulated on the spindle, bolt and washers.

(2)For mounting saw blade, the concave sides of both washers (A) and (B) must be fitted to the saw blade sides. Mount the saw blade on the spindle, and finally affix washer (B) (See Fig. 19)

(3)To assure proper rotation direction of the saw blade, the arrow direction on the saw blade must coincide with the arrow direction on the blade cover.

Tighten

Loosen

Lock Lever

Wrench

Fig. 17

	Lower Guard
Saw Blade	Blade
	Blade
	Cover

Lever

Fig. 18

17

Image 17

Contents Advertencia AvertissementÍndice ContentsTable DES Matieres Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Specific Safety Rules and Symbols Be careful of brake kickback. C7BD2 only DON’T TRY to Hold Short Places by Hand Operate power tools at the rated voltage Keep motor air vent cleanNever operate without all guards in place Use right toolCarefully handle power tools Blades and accessories must be securely mounted to the toolNever use a tool which is defective or operating abnormally Do not wipe plastic parts with solventDouble Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolName of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Adjustsing the SAW Prior to USE Regulating the guide Rip fence Adjusting the cutting depth FigAdjusting the angle of inclination Pocket Cutting Cutting ProceduresMounting the saw blade Mounting and Dismounting the SAW BladeDismounting the saw blade English Maintenance and Inspection Modifications Service parts listPage Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéConserver CES Instructions SecuriteRègles Generale DE Sécurité Sécurité personnelle Règles DE Sécurité Spécifiques ET Symboles Français Faire attention au retour de freinage. C7BD2 seulement NE PAS Essayer DE Tenir LES Sections Courtes À LA Main Utiliser l’outil motorisE a la tension nominale Garder propres les Events d’air du moteurNe pas essuyer les parties en plastique avec du solvant Manipuler l’outil motorisé avec précautionDouble Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties Description FonctionnelleAvant L’UTILISATION Vérifier le bon fonctionnement du carter de sécurité Vérifier si les leviers a sont bien serrésLunettes de protection 10. Vérifier si la lame est serréeRéglage de l’angle d’inclinaison Réglage DE LA Scie Avant L’UTILISATION AvertissementRéglage de la profondeur de coupe Fig Accessoire en option Procedures DE Coupe AvertissementDémontage de la lame Montage ET Demontage DE LA Lame DE ScieMontage de la lame Entretien ET Inspection Remplacement dun balai en carboneInspection de la lame de scie Vérifier les visPrecaucion Liste des pièces de rechangePage Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadNormas Generales DE Seguridad SeguridadGuarde Estas Instrucciones Seguridad eléctricaEspañol Normas Y Símbolos Específicos DE Seguridad Español Tenga cuidado con el contragolpe del freno ¡NO Intente Sujetar Partes Cortas CON LA Mano Utilice la herramienta correcta No toque nunca las piezas móvilesManeje correctamente la herramienta Mantenga limpio el conducto de ventilación del motorNo limpie las partes de plástico con disolvente Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Especificaciones Descripción FunctionalNomenclatura Antes DE LA Operación Montaje Y OperaciónAplicaciones Ajuste DE LA Sierra Antes DE Utilizarla Ajuste del ángulo de inclinación Ajuste de la profundidad de corte FigRegulación de la guía Guía de corte Si la palanca a estuviese floja, se podríanProcedimientos DE Corte Advertencia Desmontaje de la cuchilla de la sierra Montaje Y Desmontaje DE LA Cuchilla DE LA Sierra AdvertenciaMontaje de la cuchilla de la sierra Inspección de la cuchilla de la sierra Mantenimiento E InspecciónComprobación de los tornillos Inspección de la escobillas FigModificaciones Lista de repuestosPage Page Page Hitachi Koki Canada Co