Samsung 7100 installation manual Separation of TNV and Selv Pluggable a, Telephone line cord

Page 12

Ошибка! Стиль не определен.

Separation of TNV and SELV - Pluggable A

The separate protective earthing terminal provided on this product shall be permanently connected to earth. (Instruction)

Telephone line cord

To reduce the risk of fire, use only No. 26 AWG or larger (e.g., 24 AWG) UL Listed or CSA Certified Telecommunication Line Cord.

Safety Instructions for Rack Mount

The following or similar rack-mount instructions are included with the installation instructions:

-Elevated Operating Ambient If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

-Reduced Air Flow: Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.

-Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

-Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on over-current protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

-Reliable Earthing: Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips)."

Prohibition of Metal Accessories

Do not wear metal accessories such as rings and watches to prevent electric damages to the system.

VIII

© SAMSUNG Electronics Co., Ltd.

Image 12
Contents Installation Manual Copyright Trademarks Page Page Document Content and Organization PurposeConnecting Stations and Additional Equipment ConventionsStarting the System Reference Revision HistoryOfficeServ 7100 System Manual OfficeServ 7100 Programming ManualThis page is intentionally left blank Symbols RestrictionInstruction Use of Double-pole/neutral fusing Location Safety Instructions for Rack Mount Prohibition of Metal AccessoriesSeparation of TNV and Selv Pluggable a Telephone line cordUn-allowed Use of Selector Switch AC Power Connection InhibitedCheck of Power-off Board ResetThis page is intentionally left blank Table of Contents Connecting the Grounding Wire Connecting External BatteriesConnecting the Power Connecting StationsAbbreviation List of Figures List of Tables XVI Before Installing Safety ConditionsTemperature and Humidity Site InformationPower Conditions Power Standards Power SupplyGrounding Conditions Checking the Package Package Items Category Name Quantity RemarkUTP Cable Types This page is intentionally left blank Installing Cabinets Procedure for the System InstallationSelecting Installation Method Installing in a Rack Installing in a RackTools Required Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a WallWith a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall Connecting the Grounding Wire External GroundingCabinet Configuration Mounting and Replacing BoardsMountable Boards on Slots Cabinet Parts on the Rear Panel of the CabinetPart Function Setting Switches and Mounting Option Boards Switches of MP10/11 Board DescriptionNot-used Always default 3 digits Mounting Control BoardsMounting a Modem Board on the MP10/11 Board Mounting Control Boards Control Board TypesControl Board Mountable Slot Setting Switches and Mounting Optional Boards Mounting Interface BoardsMounting UNI Board Tepri Boards Setting Switches Setting JumpersPlim Board Mounting Interface Boards to Slots Interface Board Types and Available SlotsCategory Interface Board Slots Available ReferencesОшибка! Стиль не определен Connecting Power Fail Transfer 13 Connecting Power Fail Transfer to a 16SLI2/8SLI BoardReplacing Boards Removing Cables16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting External Batteries Connecting an External BatteryConnecting the Power Connecting the Power Single cabinet configurationConnecting C.O. Line Line ConditionsLine condition of OfficeServ Line Condition Leak Resistance Connecting the C.O. Line Connecting Common C.O. LinePin No TX + RX +Connecting T1/E1/PRI Pin No E1 Mode Tx+ Rx+Page Connecting Stations Additional Equipment Connecting StationsConnecting Analog Phones Connecting to the 4SLM of a UNI BoardConnecting to a 8SLI/16SLI2 Board P1 Port Pin NoConnecting to a 8COMBO Board RJ-45 Port of 8COMBO Board for Analog Phone ConnectionConnecting Digital Phones Connecting to the 4DLM of a UNI BoardConnecting to a 8DLI/16DLI2 Board P1-P4 Ports Pin NoDLI TIP Connecting IP Phones IP Phone LayoutConnecting to a Door Phone and a Door Lock Connecting to 8DLI/16DLI2/4DLM BoardsTx+ Rx+ MMC RelatedConnecting Additional Equipment Connecting MOH/BGM EquipmentConnecting External/Additional Page Equipment Connecting Common BellChanging System Setting About the board resetConnecting Smdr Getting access to WebMMC from a client PCSpecification of the Smdr System Category Connecting Printers 14 Connecting SmdrStarting the System Pre-CheckEnvironment Safety Conditions Starting the System If the Multi MediaMMC Card is not detectedBoard LED Status & Shut-down Numbering Extensions and C.O. Lines Checking System Operation Station Call FunctionStation Camp-On Function 3 C.O. Line Call Function 4 C.O. Line Camp-On FunctionAbbreviation KDB Installation Manual
Related manuals
Manual 407 pages 58.94 Kb