Samsung 7100 installation manual Connecting the Power, Single cabinet configuration

Page 52

CHAPTER 5. Ошибка! Стиль не определен.

5.2 Connecting the Power

Single cabinet configuration

Use the power cable provided with the OfficeServ 7100 system to connect the input power terminal on the back panel of the basic cabinet to a grounded outlet.

Figure 5.1 Connecting the Power (use of a cabinet)

5-2	© SAMSUNG Electronics Co., Ltd.

Image 52

Contents Installation Manual Copyright Trademarks Page Page Document Content and Organization PurposeConventions Connecting Stations and Additional EquipmentStarting the System Reference Revision HistoryOfficeServ 7100 System Manual OfficeServ 7100 Programming ManualThis page is intentionally left blank Restriction SymbolsInstruction Use of Double-pole/neutral fusing Location Safety Instructions for Rack Mount Prohibition of Metal AccessoriesSeparation of TNV and Selv Pluggable a Telephone line cordUn-allowed Use of Selector Switch AC Power Connection InhibitedCheck of Power-off Board ResetThis page is intentionally left blank Table of Contents Connecting the Grounding Wire Connecting External BatteriesConnecting the Power Connecting StationsAbbreviation List of Figures List of Tables XVI Before Installing Safety ConditionsTemperature and Humidity Site InformationPower Standards Power Supply Power ConditionsGrounding Conditions Package Items Category Name Quantity Remark Checking the PackageUTP Cable Types This page is intentionally left blank Procedure for the System Installation Installing CabinetsSelecting Installation Method Installing in a Rack Installing in a RackTools Required Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a WallWith a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall Connecting the Grounding Wire External GroundingCabinet Configuration Mounting and Replacing BoardsParts on the Rear Panel of the Cabinet Mountable Boards on Slots CabinetPart Function Setting Switches and Mounting Option Boards Switches of MP10/11 Board DescriptionNot-used Always default 3 digits Mounting Control BoardsMounting a Modem Board on the MP10/11 Board Control Board Types Mounting Control BoardsControl Board Mountable Slot Setting Switches and Mounting Optional Boards Mounting Interface BoardsMounting UNI Board Tepri Boards Setting Switches Setting JumpersPlim Board Mounting Interface Boards to Slots Interface Board Types and Available SlotsCategory Interface Board Slots Available ReferencesОшибка! Стиль не определен Connecting Power Fail Transfer 13 Connecting Power Fail Transfer to a 16SLI2/8SLI BoardReplacing Boards Removing Cables16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting External Batteries Connecting an External BatteryConnecting the Power Connecting the Power Single cabinet configurationLine Conditions Connecting C.O. LineLine condition of OfficeServ Line Condition Leak Resistance Connecting the C.O. Line Connecting Common C.O. LinePin No TX + RX +Connecting T1/E1/PRI Pin No E1 Mode Tx+ Rx+Page Connecting Stations Additional Equipment Connecting StationsConnecting Analog Phones Connecting to the 4SLM of a UNI BoardConnecting to a 8SLI/16SLI2 Board P1 Port Pin NoConnecting to a 8COMBO Board RJ-45 Port of 8COMBO Board for Analog Phone ConnectionConnecting Digital Phones Connecting to the 4DLM of a UNI BoardConnecting to a 8DLI/16DLI2 Board P1-P4 Ports Pin NoDLI TIP Connecting IP Phones IP Phone LayoutConnecting to a Door Phone and a Door Lock Connecting to 8DLI/16DLI2/4DLM BoardsTx+ Rx+ MMC RelatedConnecting Additional Equipment Connecting MOH/BGM EquipmentConnecting External/Additional Page Equipment Connecting Common BellChanging System Setting About the board resetGetting access to WebMMC from a client PC Connecting SmdrSpecification of the Smdr System Category Connecting Printers 14 Connecting SmdrPre-Check Starting the SystemEnvironment Safety Conditions If the Multi MediaMMC Card is not detected Starting the SystemBoard LED Status & Shut-down Numbering Extensions and C.O. Lines Station Call Function Checking System OperationStation Camp-On Function 3 C.O. Line Call Function 4 C.O. Line Camp-On FunctionAbbreviation KDB Installation Manual

Related manuals

Manual 407 pages 58.94 Kb