Samsung 7100 installation manual Starting the System, If the Multi MediaMMC Card is not detected

Page 71

OfficeServ 7100 Installation Manual

8.2 Starting the System

The procedure for starting the OfficeServ 7100 system is as follows:

1)Check if the boards and cables are properly mounted and connected to the OfficeServ 7100 cabinet.

2)Turn on the power of the OfficeServ 7100 basic cabinet, and turn on the power of the expansion cabinet.

3)Check the LEDs for the MP10/11 boards mounted on the OfficeServ 7100 cabinet. y The RUN LED of the MP10/11 board turns green and the MC LED flashes when

the system normally starts the booting process.

y Once the booting is complete, the RUN LED of the MP10/11 board flashes green, and the SM LED stops flashing and remains lighted.

y The RUN LED of the LCP board flashes when the power supply and processor status of the expansion rack is normal.

If the Multi Media(MMC Card) is not detected

If the system cannot detect the multi media, the MC LED of the MP10/11 board flash in red. In such cases, remove MMC card from MP10/11 boards and insert it again.

4)Check if the LED statuses of other interface boards are normal.

5)If the LED status of a MP10/11 or interface board is abnormal, turn off the power of the cabinet and turn the power on again.

Board LED Status & Shut-down

- Refer to the ‘OfficeServ 7100 System Manual’ for LED statuses of each board.

- Shut-down is hardly required while operating the OfficeServ 7100 system. However, when shutting down the system due to reasons such as moving the system, turn off the power of the expansion cabinet, and turn off the power of the basic cabinet.

© SAMSUNG Electronics Co., Ltd.

8-3

Image 71
Contents Installation Manual Copyright Trademarks Page Page Purpose Document Content and OrganizationStarting the System Connecting Stations and Additional EquipmentConventions OfficeServ 7100 Programming Manual ReferenceRevision History OfficeServ 7100 System ManualThis page is intentionally left blank Instruction SymbolsRestriction Use of Double-pole/neutral fusing Location Telephone line cord Safety Instructions for Rack MountProhibition of Metal Accessories Separation of TNV and Selv Pluggable aBoard Reset Un-allowed Use of Selector SwitchAC Power Connection Inhibited Check of Power-offThis page is intentionally left blank Table of Contents Connecting Stations Connecting the Grounding WireConnecting External Batteries Connecting the PowerAbbreviation List of Figures List of Tables XVI Site Information Before InstallingSafety Conditions Temperature and HumidityGrounding Conditions Power ConditionsPower Standards Power Supply UTP Cable Types Checking the PackagePackage Items Category Name Quantity Remark This page is intentionally left blank Selecting Installation Method Installing CabinetsProcedure for the System Installation Tools Required Installing in a RackInstalling in a Rack Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a WallWith a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall External Grounding Connecting the Grounding WireMounting and Replacing Boards Cabinet ConfigurationPart Function Mountable Boards on Slots CabinetParts on the Rear Panel of the Cabinet Mounting Control Boards Setting Switches and Mounting Option BoardsSwitches of MP10/11 Board Description Not-used Always default 3 digitsMounting a Modem Board on the MP10/11 Board Control Board Mountable Slot Mounting Control BoardsControl Board Types Mounting Interface Boards Setting Switches and Mounting Optional BoardsMounting UNI Board Tepri Boards Setting Jumpers Setting SwitchesPlim Board References Mounting Interface Boards to SlotsInterface Board Types and Available Slots Category Interface Board Slots AvailableОшибка! Стиль не определен 13 Connecting Power Fail Transfer to a 16SLI2/8SLI Board Connecting Power Fail TransferRemoving Cables Replacing Boards16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting an External Battery Connecting External BatteriesConnecting the Power Single cabinet configuration Connecting the PowerLine condition of OfficeServ Line Condition Leak Resistance Connecting C.O. LineLine Conditions TX + RX + Connecting the C.O. LineConnecting Common C.O. Line Pin NoPin No E1 Mode Tx+ Rx+ Connecting T1/E1/PRIPage Connecting Stations Connecting Stations Additional EquipmentP1 Port Pin No Connecting Analog PhonesConnecting to the 4SLM of a UNI Board Connecting to a 8SLI/16SLI2 BoardRJ-45 Port of 8COMBO Board for Analog Phone Connection Connecting to a 8COMBO BoardP1-P4 Ports Pin No Connecting Digital PhonesConnecting to the 4DLM of a UNI Board Connecting to a 8DLI/16DLI2 BoardDLI TIP IP Phone Layout Connecting IP PhonesMMC Related Connecting to a Door Phone and a Door LockConnecting to 8DLI/16DLI2/4DLM Boards Tx+ Rx+Connecting MOH/BGM Equipment Connecting Additional EquipmentConnecting Common Bell Connecting External/Additional Page EquipmentAbout the board reset Changing System SettingSpecification of the Smdr System Category Connecting SmdrGetting access to WebMMC from a client PC 14 Connecting Smdr Connecting PrintersEnvironment Starting the SystemPre-Check Safety Conditions Board LED Status & Shut-down Starting the SystemIf the Multi MediaMMC Card is not detected Numbering Extensions and C.O. Lines Station Camp-On Function Checking System OperationStation Call Function 4 C.O. Line Camp-On Function 3 C.O. Line Call FunctionAbbreviation KDB Installation Manual
Related manuals
Manual 407 pages 58.94 Kb