Samsung 7100 installation manual Plim Board

Page 42

CHAPTER 3. Ошибка! Стиль не определен.

3.3.1.5 PLIM Board

The OfficeServ 7100 system does not support the power to the PLM board. Therefore, the PLIM board does not support PoE and only performs the same function as that of the LIM board.

When the PLIM board is used, the board should be mounted after removing Shunt pin J1, J2 and J3 supplying the PoE Power.

1

1

1

J1 J2

J3

Figure 3.10 PLIM Board

3-10	© SAMSUNG Electronics Co., Ltd.

Image 42

Contents Installation Manual Copyright Trademarks Page Page Document Content and Organization PurposeConnecting Stations and Additional Equipment ConventionsStarting the System OfficeServ 7100 System Manual ReferenceRevision History OfficeServ 7100 Programming ManualThis page is intentionally left blank Symbols RestrictionInstruction Use of Double-pole/neutral fusing Location Separation of TNV and Selv Pluggable a Safety Instructions for Rack MountProhibition of Metal Accessories Telephone line cordCheck of Power-off Un-allowed Use of Selector SwitchAC Power Connection Inhibited Board ResetThis page is intentionally left blank Table of Contents Connecting the Power Connecting the Grounding WireConnecting External Batteries Connecting StationsAbbreviation List of Figures List of Tables XVI Temperature and Humidity Before InstallingSafety Conditions Site InformationPower Conditions Power Standards Power SupplyGrounding Conditions Checking the Package Package Items Category Name Quantity RemarkUTP Cable Types This page is intentionally left blank Installing Cabinets Procedure for the System InstallationSelecting Installation Method Installing in a Rack Installing in a RackTools Required Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a WallWith a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall Connecting the Grounding Wire External GroundingCabinet Configuration Mounting and Replacing BoardsMountable Boards on Slots Cabinet Parts on the Rear Panel of the CabinetPart Function Not-used Always default 3 digits Setting Switches and Mounting Option BoardsSwitches of MP10/11 Board Description Mounting Control BoardsMounting a Modem Board on the MP10/11 Board Mounting Control Boards Control Board TypesControl Board Mountable Slot Setting Switches and Mounting Optional Boards Mounting Interface BoardsMounting UNI Board Tepri Boards Setting Switches Setting JumpersPlim Board Category Interface Board Slots Available Mounting Interface Boards to SlotsInterface Board Types and Available Slots ReferencesОшибка! Стиль не определен Connecting Power Fail Transfer 13 Connecting Power Fail Transfer to a 16SLI2/8SLI BoardReplacing Boards Removing Cables16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting External Batteries Connecting an External BatteryConnecting the Power Connecting the Power Single cabinet configurationConnecting C.O. Line Line ConditionsLine condition of OfficeServ Line Condition Leak Resistance Pin No Connecting the C.O. LineConnecting Common C.O. Line TX + RX +Connecting T1/E1/PRI Pin No E1 Mode Tx+ Rx+Page Connecting Stations Additional Equipment Connecting StationsConnecting to a 8SLI/16SLI2 Board Connecting Analog PhonesConnecting to the 4SLM of a UNI Board P1 Port Pin NoConnecting to a 8COMBO Board RJ-45 Port of 8COMBO Board for Analog Phone ConnectionConnecting to a 8DLI/16DLI2 Board Connecting Digital PhonesConnecting to the 4DLM of a UNI Board P1-P4 Ports Pin NoDLI TIP Connecting IP Phones IP Phone LayoutTx+ Rx+ Connecting to a Door Phone and a Door LockConnecting to 8DLI/16DLI2/4DLM Boards MMC RelatedConnecting Additional Equipment Connecting MOH/BGM EquipmentConnecting External/Additional Page Equipment Connecting Common BellChanging System Setting About the board resetConnecting Smdr Getting access to WebMMC from a client PCSpecification of the Smdr System Category Connecting Printers 14 Connecting SmdrStarting the System Pre-CheckEnvironment Safety Conditions Starting the System If the Multi MediaMMC Card is not detectedBoard LED Status & Shut-down Numbering Extensions and C.O. Lines Checking System Operation Station Call FunctionStation Camp-On Function 3 C.O. Line Call Function 4 C.O. Line Camp-On FunctionAbbreviation KDB Installation Manual

Related manuals

Manual 407 pages 58.94 Kb