Samsung 7100 Un-allowed Use of Selector Switch, AC Power Connection Inhibited, Check of Power-off

Page 13

OfficeServ 7100 Installation Manual

Un-allowed Use of Selector Switch

The OfficeServ 7100 system only use 230 V. Do not change the input power freely by means of the selector switch.

AC Power Connection Inhibited

Do not operate other devices with the AC power of the OfficeServ 7100 system or with the DC power of external batteries.

Check of Power-off

Check if the cabinet power is off when mounting boards on slots. Inserting or ejecting a board while the power is on may damage the board.

Board Reset

New settings are applied only after the board is reset. The system may malfunction if the board is not properly initialized.

Caution for Installation

Only a trained service staff can install the OfficeServ 7100 system.

© SAMSUNG Electronics Co., Ltd.

IX

Image 13
Contents Installation Manual Copyright Trademarks Page Page Purpose Document Content and OrganizationConventions Connecting Stations and Additional EquipmentStarting the System Revision History ReferenceOfficeServ 7100 System Manual OfficeServ 7100 Programming ManualThis page is intentionally left blank Restriction SymbolsInstruction Use of Double-pole/neutral fusing Location Prohibition of Metal Accessories Safety Instructions for Rack MountSeparation of TNV and Selv Pluggable a Telephone line cordAC Power Connection Inhibited Un-allowed Use of Selector SwitchCheck of Power-off Board ResetThis page is intentionally left blank Table of Contents Connecting External Batteries Connecting the Grounding WireConnecting the Power Connecting StationsAbbreviation List of Figures List of Tables XVI Safety Conditions Before InstallingTemperature and Humidity Site InformationPower Standards Power Supply Power ConditionsGrounding Conditions Package Items Category Name Quantity Remark Checking the PackageUTP Cable Types This page is intentionally left blank Procedure for the System Installation Installing CabinetsSelecting Installation Method Installing in a Rack Installing in a RackTools Required Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a WallWith a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall External Grounding Connecting the Grounding WireMounting and Replacing Boards Cabinet ConfigurationParts on the Rear Panel of the Cabinet Mountable Boards on Slots CabinetPart Function Switches of MP10/11 Board Description Setting Switches and Mounting Option BoardsNot-used Always default 3 digits Mounting Control BoardsMounting a Modem Board on the MP10/11 Board Control Board Types Mounting Control BoardsControl Board Mountable Slot Mounting Interface Boards Setting Switches and Mounting Optional BoardsMounting UNI Board Tepri Boards Setting Jumpers Setting SwitchesPlim Board Interface Board Types and Available Slots Mounting Interface Boards to SlotsCategory Interface Board Slots Available ReferencesОшибка! Стиль не определен 13 Connecting Power Fail Transfer to a 16SLI2/8SLI Board Connecting Power Fail TransferRemoving Cables Replacing Boards16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting an External Battery Connecting External BatteriesConnecting the Power Single cabinet configuration Connecting the PowerLine Conditions Connecting C.O. LineLine condition of OfficeServ Line Condition Leak Resistance Connecting Common C.O. Line Connecting the C.O. LinePin No TX + RX +Pin No E1 Mode Tx+ Rx+ Connecting T1/E1/PRIPage Connecting Stations Connecting Stations Additional EquipmentConnecting to the 4SLM of a UNI Board Connecting Analog PhonesConnecting to a 8SLI/16SLI2 Board P1 Port Pin NoRJ-45 Port of 8COMBO Board for Analog Phone Connection Connecting to a 8COMBO BoardConnecting to the 4DLM of a UNI Board Connecting Digital PhonesConnecting to a 8DLI/16DLI2 Board P1-P4 Ports Pin NoDLI TIP IP Phone Layout Connecting IP PhonesConnecting to 8DLI/16DLI2/4DLM Boards Connecting to a Door Phone and a Door LockTx+ Rx+ MMC RelatedConnecting MOH/BGM Equipment Connecting Additional EquipmentConnecting Common Bell Connecting External/Additional Page EquipmentAbout the board reset Changing System SettingGetting access to WebMMC from a client PC Connecting SmdrSpecification of the Smdr System Category 14 Connecting Smdr Connecting PrintersPre-Check Starting the SystemEnvironment Safety Conditions If the Multi MediaMMC Card is not detected Starting the SystemBoard LED Status & Shut-down Numbering Extensions and C.O. Lines Station Call Function Checking System OperationStation Camp-On Function 4 C.O. Line Camp-On Function 3 C.O. Line Call FunctionAbbreviation KDB Installation Manual
Related manuals
Manual 407 pages 58.94 Kb