Samsung 7100 installation manual Location

Page 11

OfficeServ 7100 Installation Manual

CAUTION

Caution for Installation

Only a trained service staff can install the OfficeServ 7100 system.

The equipment intended only for installation in a RESTRICTED ACCESS

LOCATION

Caution for the connection of External Batteries

Do not connect an external AC power until the battery and the system is completely disconnected. To do so may cause electric shock to the constructor or the system.

Make sure that the specified polarities(+, -) are correctly connected when connecting external batteries.

To reduce risk of fire and injury to persons, use only a sealed nickel cadmium or lead-acid battery supply capable of handling a charge current of 0.25 A, a charge voltage of -54 V dc and a discharge rate of 26 Ah.

Leakage currents due to ringing voltage – Earthing installation instructions

1.A supplementary equipment earthing conductor is to be installed between the product or system and earth, that is, in addition to the equipment earthing conductor in the power supply cord.

2.The supplementary equipment earthing conductor may not be smaller in size than the unearthed branch-circuit supply conductors. The supplementary equipment earthing conductor is to be connected to the product at the terminal provided, and connected to earth in a manner that will retain the earth connection when the power supply cord is unplugged. The connection to earth of the supplementary earthing conductor shall be in compliance with the appropriate rules for terminating bonding jumpers in Part K of Article 250 of the National Electrical Code, ANSI/NFPA 70 and Article 10 of Part 1 of the Canadian Electrical Code, Part 1, C22.1. Termination of the

supplementary earthing conductor is permitted to be made to building steel, to a metal electrical raceway system, or to any earthed item that is permanently and reliably connected to the electrical service equipment earthed.

3.Bare, covered, or insulated earthing conductors are acceptable. A covered or insulated conductor must have a continuous outer finish that is either green, or green with one or more yellow stripes.

© SAMSUNG Electronics Co., Ltd.

VII

Image 11
Contents Installation Manual Copyright Trademarks Page Page Purpose Document Content and OrganizationStarting the System Connecting Stations and Additional EquipmentConventions OfficeServ 7100 Programming Manual ReferenceRevision History OfficeServ 7100 System ManualThis page is intentionally left blank Instruction SymbolsRestriction Use of Double-pole/neutral fusing Location Telephone line cord Safety Instructions for Rack MountProhibition of Metal Accessories Separation of TNV and Selv Pluggable aBoard Reset Un-allowed Use of Selector SwitchAC Power Connection Inhibited Check of Power-offThis page is intentionally left blank Table of Contents Connecting Stations Connecting the Grounding WireConnecting External Batteries Connecting the PowerAbbreviation List of Figures List of Tables XVI Site Information Before InstallingSafety Conditions Temperature and HumidityGrounding Conditions Power ConditionsPower Standards Power Supply UTP Cable Types Checking the PackagePackage Items Category Name Quantity Remark This page is intentionally left blank Selecting Installation Method Installing CabinetsProcedure for the System Installation Tools Required Installing in a RackInstalling in a Rack Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a WallWith a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall External Grounding Connecting the Grounding WireMounting and Replacing Boards Cabinet ConfigurationPart Function Mountable Boards on Slots CabinetParts on the Rear Panel of the Cabinet Mounting Control Boards Setting Switches and Mounting Option BoardsSwitches of MP10/11 Board Description Not-used Always default 3 digitsMounting a Modem Board on the MP10/11 Board Control Board Mountable Slot Mounting Control BoardsControl Board Types Mounting Interface Boards Setting Switches and Mounting Optional BoardsMounting UNI Board Tepri Boards Setting Jumpers Setting SwitchesPlim Board References Mounting Interface Boards to SlotsInterface Board Types and Available Slots Category Interface Board Slots AvailableОшибка! Стиль не определен 13 Connecting Power Fail Transfer to a 16SLI2/8SLI Board Connecting Power Fail TransferRemoving Cables Replacing Boards16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting an External Battery Connecting External BatteriesConnecting the Power Single cabinet configuration Connecting the PowerLine condition of OfficeServ Line Condition Leak Resistance Connecting C.O. LineLine Conditions TX + RX + Connecting the C.O. LineConnecting Common C.O. Line Pin NoPin No E1 Mode Tx+ Rx+ Connecting T1/E1/PRIPage Connecting Stations Connecting Stations Additional EquipmentP1 Port Pin No Connecting Analog PhonesConnecting to the 4SLM of a UNI Board Connecting to a 8SLI/16SLI2 BoardRJ-45 Port of 8COMBO Board for Analog Phone Connection Connecting to a 8COMBO BoardP1-P4 Ports Pin No Connecting Digital PhonesConnecting to the 4DLM of a UNI Board Connecting to a 8DLI/16DLI2 BoardDLI TIP IP Phone Layout Connecting IP PhonesMMC Related Connecting to a Door Phone and a Door LockConnecting to 8DLI/16DLI2/4DLM Boards Tx+ Rx+Connecting MOH/BGM Equipment Connecting Additional EquipmentConnecting Common Bell Connecting External/Additional Page EquipmentAbout the board reset Changing System SettingSpecification of the Smdr System Category Connecting SmdrGetting access to WebMMC from a client PC 14 Connecting Smdr Connecting PrintersEnvironment Starting the SystemPre-Check Safety Conditions Board LED Status & Shut-down Starting the SystemIf the Multi MediaMMC Card is not detected Numbering Extensions and C.O. Lines Station Camp-On Function Checking System OperationStation Call Function 4 C.O. Line Camp-On Function 3 C.O. Line Call FunctionAbbreviation KDB Installation Manual
Related manuals
Manual 407 pages 58.94 Kb