Samsung 7100 installation manual Safety Conditions

Page 70

CHAPTER 8. Ошибка! Стиль не определен.

8.1.2 Safety Conditions

The building where the OfficeServ 7100 system is installed should have lightning rods and grounding to protect the system against lightning and electric leakage.

yCheck if the OfficeServ 7100 system is not inclined and is maintained horizontally.

yDo not place devices that may cause electromagnetic interference near the system.

yPlace a fire extinguisher near the system. Since spring coolers can seriously damage the system, use extinguishers such as Halor 1301 and Carbon Dioxide.

yMake sure that the input power of the OfficeServ 7100 system should be AC 230 V and do not use together with other electric devices, such as motors and compressors.

yCheck if the AC voltage switch of the PSU is properly set according to the voltage of the input power, 230 VAC.

yCheck if the grounding terminal on the rear panel of the system is properly connected to the external grounding.

8-2

© SAMSUNG Electronics Co., Ltd.

Image 70
Contents Installation Manual Copyright Trademarks Page Page Document Content and Organization PurposeConventions Connecting Stations and Additional EquipmentStarting the System OfficeServ 7100 System Manual ReferenceRevision History OfficeServ 7100 Programming ManualThis page is intentionally left blank Restriction SymbolsInstruction Use of Double-pole/neutral fusing Location Separation of TNV and Selv Pluggable a Safety Instructions for Rack MountProhibition of Metal Accessories Telephone line cordCheck of Power-off Un-allowed Use of Selector SwitchAC Power Connection Inhibited Board ResetThis page is intentionally left blank Table of Contents Connecting the Power Connecting the Grounding WireConnecting External Batteries Connecting StationsAbbreviation List of Figures List of Tables XVI Temperature and Humidity Before InstallingSafety Conditions Site InformationPower Standards Power Supply Power ConditionsGrounding Conditions Package Items Category Name Quantity Remark Checking the PackageUTP Cable Types This page is intentionally left blank Procedure for the System Installation Installing CabinetsSelecting Installation Method Installing in a Rack Installing in a RackTools Required Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a WallWith a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall Connecting the Grounding Wire External GroundingCabinet Configuration Mounting and Replacing BoardsParts on the Rear Panel of the Cabinet Mountable Boards on Slots CabinetPart Function Not-used Always default 3 digits Setting Switches and Mounting Option BoardsSwitches of MP10/11 Board Description Mounting Control BoardsMounting a Modem Board on the MP10/11 Board Control Board Types Mounting Control BoardsControl Board Mountable Slot Setting Switches and Mounting Optional Boards Mounting Interface BoardsMounting UNI Board Tepri Boards Setting Switches Setting JumpersPlim Board Category Interface Board Slots Available Mounting Interface Boards to SlotsInterface Board Types and Available Slots ReferencesОшибка! Стиль не определен Connecting Power Fail Transfer 13 Connecting Power Fail Transfer to a 16SLI2/8SLI BoardReplacing Boards Removing Cables16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting External Batteries Connecting an External BatteryConnecting the Power Connecting the Power Single cabinet configurationLine Conditions Connecting C.O. LineLine condition of OfficeServ Line Condition Leak Resistance Pin No Connecting the C.O. LineConnecting Common C.O. Line TX + RX +Connecting T1/E1/PRI Pin No E1 Mode Tx+ Rx+Page Connecting Stations Additional Equipment Connecting StationsConnecting to a 8SLI/16SLI2 Board Connecting Analog PhonesConnecting to the 4SLM of a UNI Board P1 Port Pin NoConnecting to a 8COMBO Board RJ-45 Port of 8COMBO Board for Analog Phone ConnectionConnecting to a 8DLI/16DLI2 Board Connecting Digital PhonesConnecting to the 4DLM of a UNI Board P1-P4 Ports Pin NoDLI TIP Connecting IP Phones IP Phone LayoutTx+ Rx+ Connecting to a Door Phone and a Door LockConnecting to 8DLI/16DLI2/4DLM Boards MMC RelatedConnecting Additional Equipment Connecting MOH/BGM EquipmentConnecting External/Additional Page Equipment Connecting Common BellChanging System Setting About the board resetGetting access to WebMMC from a client PC Connecting SmdrSpecification of the Smdr System Category Connecting Printers 14 Connecting SmdrPre-Check Starting the SystemEnvironment Safety Conditions If the Multi MediaMMC Card is not detected Starting the SystemBoard LED Status & Shut-down Numbering Extensions and C.O. Lines Station Call Function Checking System OperationStation Camp-On Function 3 C.O. Line Call Function 4 C.O. Line Camp-On FunctionAbbreviation KDB Installation Manual
Related manuals
Manual 407 pages 58.94 Kb