Samsung installation manual Reference, Revision History, OfficeServ 7100 System Manual

Page 7

OfficeServ 7100 Installation Manual

Reference

OfficeServ 7100 System Manual

This document introduces OfficeServ 7100 and describes the system information, such as hard configuration, specification, and functions, necessary for this system.

OfficeServ 7100 Programming Manual

This document describes how to use the MMC program to change the OfficeServ 7100 system setting by using a phone.

Revision History

EDITION

DATE OF ISSUE

REMARKS

00

08. 2006.

Original Draft

 

 

 

01

01.2007.

Safety, VM and Router etc.

 

 

 

02

04.2007.

DoC, 2BRM Modular Jack Connection

 

 

 

© SAMSUNG Electronics Co., Ltd.

III

Image 7
Contents Installation Manual Copyright Trademarks Page Page Purpose Document Content and OrganizationConventions Connecting Stations and Additional EquipmentStarting the System OfficeServ 7100 Programming Manual ReferenceRevision History OfficeServ 7100 System ManualThis page is intentionally left blank Restriction SymbolsInstruction Use of Double-pole/neutral fusing Location Telephone line cord Safety Instructions for Rack MountProhibition of Metal Accessories Separation of TNV and Selv Pluggable aBoard Reset Un-allowed Use of Selector SwitchAC Power Connection Inhibited Check of Power-offThis page is intentionally left blank Table of Contents Connecting Stations Connecting the Grounding WireConnecting External Batteries Connecting the PowerAbbreviation List of Figures List of Tables XVI Site Information Before InstallingSafety Conditions Temperature and HumidityPower Standards Power Supply Power ConditionsGrounding Conditions Package Items Category Name Quantity Remark Checking the PackageUTP Cable Types This page is intentionally left blank Procedure for the System Installation Installing CabinetsSelecting Installation Method Installing in a Rack Installing in a RackTools Required Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a WallWith a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall External Grounding Connecting the Grounding WireMounting and Replacing Boards Cabinet ConfigurationParts on the Rear Panel of the Cabinet Mountable Boards on Slots CabinetPart Function Mounting Control Boards Setting Switches and Mounting Option BoardsSwitches of MP10/11 Board Description Not-used Always default 3 digitsMounting a Modem Board on the MP10/11 Board Control Board Types Mounting Control BoardsControl Board Mountable Slot Mounting Interface Boards Setting Switches and Mounting Optional BoardsMounting UNI Board Tepri Boards Setting Jumpers Setting SwitchesPlim Board References Mounting Interface Boards to SlotsInterface Board Types and Available Slots Category Interface Board Slots AvailableОшибка! Стиль не определен 13 Connecting Power Fail Transfer to a 16SLI2/8SLI Board Connecting Power Fail TransferRemoving Cables Replacing Boards16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting an External Battery Connecting External BatteriesConnecting the Power Single cabinet configuration Connecting the PowerLine Conditions Connecting C.O. LineLine condition of OfficeServ Line Condition Leak Resistance TX + RX + Connecting the C.O. LineConnecting Common C.O. Line Pin NoPin No E1 Mode Tx+ Rx+ Connecting T1/E1/PRIPage Connecting Stations Connecting Stations Additional EquipmentP1 Port Pin No Connecting Analog PhonesConnecting to the 4SLM of a UNI Board Connecting to a 8SLI/16SLI2 BoardRJ-45 Port of 8COMBO Board for Analog Phone Connection Connecting to a 8COMBO BoardP1-P4 Ports Pin No Connecting Digital PhonesConnecting to the 4DLM of a UNI Board Connecting to a 8DLI/16DLI2 BoardDLI TIP IP Phone Layout Connecting IP PhonesMMC Related Connecting to a Door Phone and a Door LockConnecting to 8DLI/16DLI2/4DLM Boards Tx+ Rx+Connecting MOH/BGM Equipment Connecting Additional EquipmentConnecting Common Bell Connecting External/Additional Page EquipmentAbout the board reset Changing System SettingGetting access to WebMMC from a client PC Connecting SmdrSpecification of the Smdr System Category 14 Connecting Smdr Connecting PrintersPre-Check Starting the SystemEnvironment Safety Conditions If the Multi MediaMMC Card is not detected Starting the SystemBoard LED Status & Shut-down Numbering Extensions and C.O. Lines Station Call Function Checking System OperationStation Camp-On Function 4 C.O. Line Camp-On Function 3 C.O. Line Call FunctionAbbreviation KDB Installation Manual
Related manuals
Manual 407 pages 58.94 Kb