Samsung 7100 Conventions, Connecting Stations and Additional Equipment, Starting the System

Page 6

Ошибка! Стиль не определен.

CHAPTER 7. Connecting Stations and Additional Equipment

This chapter describes how to connect various stations and additional equipment, such as analog/digital phones, door phones and door locks, to the OfficeServ 7100 system.

CHAPTER 8. Starting the System

This chapter describes items to check before starting the OfficeServ 7100 system, the procedure for starting the system, and the procedure for testing whether the system is normally operating after startup.

ABBREVIATION

Abbreviations frequently used in this document are described.

Conventions

The following types of paragraphs contain special information that must be carefully read and thoroughly understood. Such information may or may not be enclosed in a rectangular box, separating it from the main text, but is always preceded by an icon and/or a bold title.

WARNING

Provides information or instructions that the reader should follow in order to avoid personal injury or fatality.

CAUTION

Provides information or instructions that the reader should follow in order to avoid a service failure or damage to the system.

CHECKPOINT

Provides the operator with checkpoints for stable system operation.

NOTE

Indicates additional information as a reference.

II

© SAMSUNG Electronics Co., Ltd.

Image 6
Contents Installation Manual Copyright Trademarks Page Page Document Content and Organization PurposeConnecting Stations and Additional Equipment ConventionsStarting the System OfficeServ 7100 System Manual ReferenceRevision History OfficeServ 7100 Programming ManualThis page is intentionally left blank Symbols RestrictionInstruction Use of Double-pole/neutral fusing Location Separation of TNV and Selv Pluggable a Safety Instructions for Rack MountProhibition of Metal Accessories Telephone line cordCheck of Power-off Un-allowed Use of Selector SwitchAC Power Connection Inhibited Board ResetThis page is intentionally left blank Table of Contents Connecting the Power Connecting the Grounding WireConnecting External Batteries Connecting StationsAbbreviation List of Figures List of Tables XVI Temperature and Humidity Before InstallingSafety Conditions Site InformationPower Conditions Power Standards Power SupplyGrounding Conditions Checking the Package Package Items Category Name Quantity RemarkUTP Cable Types This page is intentionally left blank Installing Cabinets Procedure for the System InstallationSelecting Installation Method Installing in a Rack Installing in a RackTools Required Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a WallWith a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall Connecting the Grounding Wire External GroundingCabinet Configuration Mounting and Replacing BoardsMountable Boards on Slots Cabinet Parts on the Rear Panel of the CabinetPart Function Not-used Always default 3 digits Setting Switches and Mounting Option BoardsSwitches of MP10/11 Board Description Mounting Control BoardsMounting a Modem Board on the MP10/11 Board Mounting Control Boards Control Board TypesControl Board Mountable Slot Setting Switches and Mounting Optional Boards Mounting Interface BoardsMounting UNI Board Tepri Boards Setting Switches Setting JumpersPlim Board Category Interface Board Slots Available Mounting Interface Boards to SlotsInterface Board Types and Available Slots ReferencesОшибка! Стиль не определен Connecting Power Fail Transfer 13 Connecting Power Fail Transfer to a 16SLI2/8SLI BoardReplacing Boards Removing Cables16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting External Batteries Connecting an External BatteryConnecting the Power Connecting the Power Single cabinet configurationConnecting C.O. Line Line ConditionsLine condition of OfficeServ Line Condition Leak Resistance Pin No Connecting the C.O. LineConnecting Common C.O. Line TX + RX +Connecting T1/E1/PRI Pin No E1 Mode Tx+ Rx+Page Connecting Stations Additional Equipment Connecting StationsConnecting to a 8SLI/16SLI2 Board Connecting Analog PhonesConnecting to the 4SLM of a UNI Board P1 Port Pin NoConnecting to a 8COMBO Board RJ-45 Port of 8COMBO Board for Analog Phone ConnectionConnecting to a 8DLI/16DLI2 Board Connecting Digital PhonesConnecting to the 4DLM of a UNI Board P1-P4 Ports Pin NoDLI TIP Connecting IP Phones IP Phone LayoutTx+ Rx+ Connecting to a Door Phone and a Door LockConnecting to 8DLI/16DLI2/4DLM Boards MMC RelatedConnecting Additional Equipment Connecting MOH/BGM EquipmentConnecting External/Additional Page Equipment Connecting Common BellChanging System Setting About the board resetConnecting Smdr Getting access to WebMMC from a client PCSpecification of the Smdr System Category Connecting Printers 14 Connecting SmdrStarting the System Pre-CheckEnvironment Safety Conditions Starting the System If the Multi MediaMMC Card is not detectedBoard LED Status & Shut-down Numbering Extensions and C.O. Lines Checking System Operation Station Call FunctionStation Camp-On Function 3 C.O. Line Call Function 4 C.O. Line Camp-On FunctionAbbreviation KDB Installation Manual
Related manuals
Manual 407 pages 58.94 Kb