Samsung 7100 installation manual Mounting and Replacing Boards, Cabinet Configuration

Page 33

OfficeServ 7100 Installation Manual

CHAPTER 3. Mounting and Replacing

Boards

This chapter describes how to mount and replace various boards of the OfficeServ 7100 system.

3.1 Cabinet Configuration

The cabinet of the OfficeServ 7100 System has three slots that can install boards.

Front

Slot 0

Slot 1

Slot 2

 

 

 

 

 

Rear

Figure 3.1 Front/rear View of OfficeServ 7100 Cabinet

© SAMSUNG Electronics Co., Ltd.

3-1

Image 33
Contents Installation Manual Copyright Trademarks Page Page Purpose Document Content and OrganizationConnecting Stations and Additional Equipment ConventionsStarting the System Revision History ReferenceOfficeServ 7100 System Manual OfficeServ 7100 Programming ManualThis page is intentionally left blank Symbols RestrictionInstruction Use of Double-pole/neutral fusing Location Prohibition of Metal Accessories Safety Instructions for Rack MountSeparation of TNV and Selv Pluggable a Telephone line cordAC Power Connection Inhibited Un-allowed Use of Selector SwitchCheck of Power-off Board ResetThis page is intentionally left blank Table of Contents Connecting External Batteries Connecting the Grounding WireConnecting the Power Connecting StationsAbbreviation List of Figures List of Tables XVI Safety Conditions Before InstallingTemperature and Humidity Site InformationPower Conditions Power Standards Power SupplyGrounding Conditions Checking the Package Package Items Category Name Quantity RemarkUTP Cable Types This page is intentionally left blank Installing Cabinets Procedure for the System InstallationSelecting Installation Method Installing in a Rack Installing in a RackTools Required Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a WallWith a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall External Grounding Connecting the Grounding WireMounting and Replacing Boards Cabinet ConfigurationMountable Boards on Slots Cabinet Parts on the Rear Panel of the CabinetPart Function Switches of MP10/11 Board Description Setting Switches and Mounting Option BoardsNot-used Always default 3 digits Mounting Control BoardsMounting a Modem Board on the MP10/11 Board Mounting Control Boards Control Board TypesControl Board Mountable Slot Mounting Interface Boards Setting Switches and Mounting Optional BoardsMounting UNI Board Tepri Boards Setting Jumpers Setting SwitchesPlim Board Interface Board Types and Available Slots Mounting Interface Boards to SlotsCategory Interface Board Slots Available ReferencesОшибка! Стиль не определен 13 Connecting Power Fail Transfer to a 16SLI2/8SLI Board Connecting Power Fail TransferRemoving Cables Replacing Boards16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting an External Battery Connecting External BatteriesConnecting the Power Single cabinet configuration Connecting the PowerConnecting C.O. Line Line ConditionsLine condition of OfficeServ Line Condition Leak Resistance Connecting Common C.O. Line Connecting the C.O. LinePin No TX + RX +Pin No E1 Mode Tx+ Rx+ Connecting T1/E1/PRIPage Connecting Stations Connecting Stations Additional EquipmentConnecting to the 4SLM of a UNI Board Connecting Analog PhonesConnecting to a 8SLI/16SLI2 Board P1 Port Pin NoRJ-45 Port of 8COMBO Board for Analog Phone Connection Connecting to a 8COMBO BoardConnecting to the 4DLM of a UNI Board Connecting Digital PhonesConnecting to a 8DLI/16DLI2 Board P1-P4 Ports Pin NoDLI TIP IP Phone Layout Connecting IP PhonesConnecting to 8DLI/16DLI2/4DLM Boards Connecting to a Door Phone and a Door LockTx+ Rx+ MMC RelatedConnecting MOH/BGM Equipment Connecting Additional EquipmentConnecting Common Bell Connecting External/Additional Page EquipmentAbout the board reset Changing System SettingConnecting Smdr Getting access to WebMMC from a client PCSpecification of the Smdr System Category 14 Connecting Smdr Connecting PrintersStarting the System Pre-CheckEnvironment Safety Conditions Starting the System If the Multi MediaMMC Card is not detectedBoard LED Status & Shut-down Numbering Extensions and C.O. Lines Checking System Operation Station Call FunctionStation Camp-On Function 4 C.O. Line Camp-On Function 3 C.O. Line Call FunctionAbbreviation KDB Installation Manual
Related manuals
Manual 407 pages 58.94 Kb