Samsung 7100 installation manual Mounting a Modem Board on the MP10/11 Board

Page 36

CHAPTER 3. Ошибка! Стиль не определен.

2)A modem board is mounted to connector P7/P8 of the MP10/11 board.

When mounting a modem board, the holes on the corners of the modem should be aligned fitting with the spacer.

MODEM

Figure 3.3 Mounting a Modem Board on the MP10/11 Board

4SWM or 4DLM can be mounted to connector P11, P12 and P13 of the MP10/11 board. Screws are basically locked to the support beside P13. Unscrew and position the screws to the connector direction of 4SWM/4DLM before mounting 4SWM/4DLM. After that, tighten the screws fitting with the grooves of 4SWM/4DLM.

4SWM

Figure 3.4 Mounting 4SWM/4DLM on the MP10/11 Board

3-4	© SAMSUNG Electronics Co., Ltd.

Image 36

Contents Installation Manual Copyright Trademarks Page Page Document Content and Organization PurposeConnecting Stations and Additional Equipment ConventionsStarting the System Reference Revision HistoryOfficeServ 7100 System Manual OfficeServ 7100 Programming ManualThis page is intentionally left blank Symbols RestrictionInstruction Use of Double-pole/neutral fusing Location Safety Instructions for Rack Mount Prohibition of Metal AccessoriesSeparation of TNV and Selv Pluggable a Telephone line cordUn-allowed Use of Selector Switch AC Power Connection InhibitedCheck of Power-off Board ResetThis page is intentionally left blank Table of Contents Connecting the Grounding Wire Connecting External BatteriesConnecting the Power Connecting StationsAbbreviation List of Figures List of Tables XVI Before Installing Safety ConditionsTemperature and Humidity Site InformationPower Conditions Power Standards Power SupplyGrounding Conditions Checking the Package Package Items Category Name Quantity RemarkUTP Cable Types This page is intentionally left blank Installing Cabinets Procedure for the System InstallationSelecting Installation Method Installing in a Rack Installing in a RackTools Required Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a WallWith a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall Connecting the Grounding Wire External GroundingCabinet Configuration Mounting and Replacing BoardsMountable Boards on Slots Cabinet Parts on the Rear Panel of the CabinetPart Function Setting Switches and Mounting Option Boards Switches of MP10/11 Board DescriptionNot-used Always default 3 digits Mounting Control BoardsMounting a Modem Board on the MP10/11 Board Mounting Control Boards Control Board TypesControl Board Mountable Slot Setting Switches and Mounting Optional Boards Mounting Interface BoardsMounting UNI Board Tepri Boards Setting Switches Setting JumpersPlim Board Mounting Interface Boards to Slots Interface Board Types and Available SlotsCategory Interface Board Slots Available ReferencesОшибка! Стиль не определен Connecting Power Fail Transfer 13 Connecting Power Fail Transfer to a 16SLI2/8SLI BoardReplacing Boards Removing Cables16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting External Batteries Connecting an External BatteryConnecting the Power Connecting the Power Single cabinet configurationConnecting C.O. Line Line ConditionsLine condition of OfficeServ Line Condition Leak Resistance Connecting the C.O. Line Connecting Common C.O. LinePin No TX + RX +Connecting T1/E1/PRI Pin No E1 Mode Tx+ Rx+Page Connecting Stations Additional Equipment Connecting StationsConnecting Analog Phones Connecting to the 4SLM of a UNI BoardConnecting to a 8SLI/16SLI2 Board P1 Port Pin NoConnecting to a 8COMBO Board RJ-45 Port of 8COMBO Board for Analog Phone ConnectionConnecting Digital Phones Connecting to the 4DLM of a UNI BoardConnecting to a 8DLI/16DLI2 Board P1-P4 Ports Pin NoDLI TIP Connecting IP Phones IP Phone LayoutConnecting to a Door Phone and a Door Lock Connecting to 8DLI/16DLI2/4DLM BoardsTx+ Rx+ MMC RelatedConnecting Additional Equipment Connecting MOH/BGM EquipmentConnecting External/Additional Page Equipment Connecting Common BellChanging System Setting About the board resetConnecting Smdr Getting access to WebMMC from a client PCSpecification of the Smdr System Category Connecting Printers 14 Connecting SmdrStarting the System Pre-CheckEnvironment Safety Conditions Starting the System If the Multi MediaMMC Card is not detectedBoard LED Status & Shut-down Numbering Extensions and C.O. Lines Checking System Operation Station Call FunctionStation Camp-On Function 3 C.O. Line Call Function 4 C.O. Line Camp-On FunctionAbbreviation KDB Installation Manual

Related manuals

Manual 407 pages 58.94 Kb