DeWalt DWFP55130 instruction manual Troubleshooting Guide, Troubleshooting Codes

Page 15

Troubleshooting Guide

This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or maintenance personnel can perform some corrective actions, and others may require the assistance of a qualified DEWALT technician or your dealer.

Problem	Code
Excessive air tank pressure-safety valve pops off	1, 2
Air leaks	3
Air leaks in air tank or at air tank welds	4
Air leaks between head and valve plate	5
Air leaks from safety valve	6
Knocking noise	6
Pressure reading on the regulated pressure gauge drops when an accessory is used	7
Compressor is not supplying enough air to operate accessories	8, 9, 10, 11, 12
Regulator knob has continuous air leak	13
Regulator will not shut off air outlet	13
Motor will not run	6, 14, 15, 16, 17, 18, 19, 20

		Troubleshooting Codes
CODE	POSSIBLE CAUSE	POSSIBLE SOLUTION
1	Pressure switch does not shut off	Set the Auto/Off switch to OFF, if the unit does not shut off contact a DEWALT factory service
	motor when compressor reaches	center or a DEWALT authorized service center.
	cut-out pressure

2	Pressure switch cut-out too high	Contact a DEWALT factory service center or a DEWALT authorized service center.
3	Tube fittings are not tight enough	Tighten fittings where air can be heard escaping. Check fittings with soapy water solution. Do
		Not Overtighten.
4	Defective air tank	Air tank must be replaced. Do not repair the leak.
		WARNING: Risk of bursting. Do not drill into, weld or otherwise modify air tank or
		it will weaken. The air tank can rupture or explode.
5	Leaking seals	Contact a DEWALT factory service center or a DEWALT authorized service center.

6	Defective safety valve	Operate safety valve manually by pulling on ring. If valve still leaks, it must be replaced.

		15

English

Image 15

Contents DWFP55130 Heavy Duty 200 psi Quiet Trim Compressor Pump/Motor Speciﬁcations SpeciﬁcationsDeclared Noise Emission Values per ISO Important Safety Instructions Deﬁnitions Safety GuidelinesHazard Injury and property Attachments & Accessories TiresOver inflation of tires Could result in seriousElectrical Grounding Instructions paragraph Installation sectionAfter operation For Future US Components FIG Air Tank Drain ValvePressure Regulator Tank under Maintenance Features FIGExtension Cords InstallationPump/Motor Specifications Grounding Instructions FigOperation HOW to StopHOW to Start LocationCustomer Responsibilities MaintenanceTo Check Safety Valve Fig To Drain Tank FigStorage Service InformationGlossary It will weaken. The air tank can rupture or explode Troubleshooting GuideTroubleshooting Codes Code Possible Cause Possible SolutionTank pressure exceeds pressure Regulator is not adjusted correctlySwitch cut-in pressure Extension cord is wrong length or Check for proper fuse. You should use a time delay fuseFiche technique Fiche technique de la pompe/du moteurManipulation Déﬁnitions lignes directrices en Matière de sécuritéDirectives de sécurité importantes Conserver CES DirectivesLe débit d’air frais dans les Avertissement Risque D’ÉCLATEMENT Des blessures graves Relatives à la mise à la Terre sous InstallationDes pneus surgonflés Pourraient provoquerOculaire conforme à la norme Avertissement Risque Associé AUX Manomètre régulé Réservoir d’air Régulateur de pression CE QUI Peut SE Comment L’ÉVITER ProduireInterrupteur marcheI/arrêtO OnI /OffO Soupape de sûreté Manomètre du réservoirCaractéristiques FIG Directives relatives à la mise à la terre Fig Emplacement RallongesProtection de la tension et du circuit Utilisation De L’appareil Fig UtilisationVidange du réservoir Fig EntretienResponsabilités du client Vériﬁcation de la soupape de sûreté ﬁgAccessoires RangementInformation sur les réparations Réparations Registre en ligneGarantie complète d’un 1 an Glossaire Avertissement risque d’éclatement. Ne pas percer le Code Cause Probable Solution ProbableGuide de dépannage Codes de dépannageRallonges sous Installation ’avertissement concernant les vapeurs inflammables Especiﬁcaciones de la Bomba y el Motor Valores de emisión de ruido declarados según ISOEspeciﬁcaciones Deﬁniciones Normas de seguridad Instrucciones de seguridad importantesConserve Estas Instrucciones Opere el compresor en Si no se siguen procedimientos de mantenimiento debidos, la Advertencia Riesgo DE ExplosiónTierra en Instalación NeumáticosPuesta a tierra La no Instrucciones de ConexiónUtilice siempre equipo Piezas en movimiento. Las Elevadas ¿QUÉ Puede SUCEDER? Cómo EvitarloCaracterísticas FIG Instrucciones de conexión a tierra Fig InstalaciónCables prolongadores Voltaje y protección del circuitoLugar Cómo utilizar su unidad ﬁg OperaciónCómo drenar el tanque Fig MantenimientoResponsabilidades del cliente Cómo veriﬁcar la válvula de seguridad FigAlmacenaje AccesoriosReparaciones Póliza de Garantía Garantía completa de un año Registro en líneaGlosario Código Causa Posible Solución Posible Guía de detección de problemasCódigos de detección de problemas Problema CódigoRomper o explotar Cables prolongadores en la sección Instalación Power tools the yellow and black color scheme Copyright 2013, 2014 D EwaltFollowing are trademarks For one or more