Panasonic EY7552 operating instructions Lamp Indications

Page 12

How to charge

1. Plug the charger into the AC outlet.

NOTE:

Sparks may be produced when the plug is inserted into the AC power supply, but this is not a problem in terms of safety.

2.Connect the battery pack firmly into the charger.

1Line up the alignment marks and place the battery onto the dock on the charger.

2Slide forward in the direction of the arrow.

Alignment marks

3.During charging, the charging lamp will be Illuminated.

When charging is completed, an internal electronic switch will automatically be triggered to prevent overcharging.

• Charging will not start if the battery pack is warm (for example, immediately after heavy-duty operation).

The orange standby lamp will be flashing until the battery cools down.

Charging will then begin automatically.

4.The charge lamp (green) will flash slowly once the battery is approximately 80% charged.

5.When charging is completed, the charging lamp in green color will turn off.

6.If the temperature of the batter pack is 0°C or less, charging takes longer to fully charge the battery pack than the standard charging time.

Even when the battery is fully charged, it will have approximately 50% of the power of a fully charged battery at normal operating temperature.

7.Consult an authorized dealer if the charging lamp (green) does not turn off.

8.If a fully charged battery pack is inserted into the charger again, the charging lamp lights up. After several minutes, the charging lamp in green color will turn off.

9.Remove the battery pack while the battery pack release button is held up.

Battery pack release button

LAMP INDICATIONS

Charging is completed. (Full charge.)

Battery is approximately 80% charged.

Now charging.

Charger is plugged into the AC outlet. Ready to charge.

(Green)

(Orange)

Charging Status Lamp.

Left: green

Right: orange will be displayed.

Battery pack is cool.

The battery pack is being charged slowly to reduce the load on the battery.

Battery pack is warm.

Charging will begin when temperature of battery pack drops. If the temperature of the

battery pack is -10° or less, the charging status lamp (orange) will also start flashing .

Charging will begin when the temperature of the battery pack goes up"

Charging is not possible. Clogged with dust or malfunction of the bat-

tery pack.

Turn off

Illuminated

Flashing

- 12 -

Image 12

Contents Model No EY7552 ImportanteFunctional Description General Safety Rules Limited WarrantyElectrical Safety Personal SafetyPower Tool Use and Care Battery Tool Use and CareService Safety Rules III. for BatteryBattery Pack II. SpecificPage IV. Assembly Attaching or Removing SocketMain unit Switch and Forward/ Reverse Lever Operation OperationForward Rotation Switch Operation Indication panel Reverse Rotation Switch OperationBattery level indicator and button Variable Speed Control TriggerBattery Pack For Appropriate Use Battery Pack Li-ion Battery PackBattery Pack Life Battery RecyclingBattery Charger Charging Pack cover Terminals LabelLamp Indications VI. Maintenance VII. Tightening TorqueFactors Affecting Tighten ing Torque VIII. Accessories SpecificationsIX. Appendix Battery Pack Battery ChargerFederal Communication Commission Interference Statement Définitions des codes IP Garantie LimitéeSécurité électrique Sécurité personnelleUtilisation et soins de l’outil méca nique Utilisation et soins de la batterie de l’outilMaintenez les outils de coupe affûtés et propres Symbole Signification RéparationIII. Chargeur DE Batterie ET Batterie Auto Nome Instructions de sécurité importantesAvertissement Avertissement IV. Montage FonctionnementFixation ou retrait de la batterie autonome RemarqueGâchette de commande de vitesse Unité principaleUtilisation du commutateur pour une rotation en sens normal Panneau indicateurRecommandation pour la prise en main BatterieBatterie autonome Li-ion Témoin d’avertissement de surchauffeChargeur de batterie Recharge Pour une batterie autonome Li-ionCouvercle de la batterie autonome Bornes Rouge La suite d’un long travail de perçage VI. Entretien VII. Couple DE SERRAGEFacteurs affectant le couple de serrage VIII. Accessoires Capacites Maximum RecommandeesIX. Appendice Complément DE GarantieCaracteristiques Techniques Unite PrincipaleBatterie Autonome Chargeur DE BatteriePage Reglas DE SeguridadGenerales Garantía LimitadaSeguridad personal Uso y cuidados de herramientas eléctricasUso y cuidado de la herramienta a batería Mantenga las herramientas de corte afiladas y limpiasII. Normas DE Seguridad Específicas ServicioEsto mantendrá la seguridad de la herramienta eléctrica Símbolo Signifi cadoIII. Para EL Cargador DE Bateria Y LA Bateria Instrucciones de seguridad importantes¡ADVERTENCIA Longitud de cableAdvertencia IV. Montaje FuncionamientoInstalación o desmontaje del cubo Colocación y extracción de la bateríaFuncionamiento del inter ruptor de rotación de avance Panel de indicaciónDisparador del control de velocidad variable PrecauciónAgarre recomendado Bloque de pilas Para un uso adecuado de la bateríaBatería de Li-ión Luz de advertencia de sobrecalentamientoCargador de la batería Carga Vida útil de la bateríaReciclado de la batería AtenciónEnchufe el cargador en la fuente de alimentación de CA VI.MANTENIMIENTO VII. PAR DE AprieteFactores que afectan al par de apriete VIII. Accesorios IX. AnexoMáximas Capacidades Recomendadas Información Adicional Sobre LA GarantíaEspecificaciones Unidad PrincipalBatería Cargador DE BateríaPage Memo Memo Memo Two Riverfront Plaza, Newark, NJ EY981075521