Hitachi Koki USA CW 20 Assembly and Adjustments, Mounting the Scroll SAW FIG. A, B

Page 11

English

ASSEMBLY AND ADJUSTMENTS

ESTIMATED ASSEMBLY TIME 15~20 MINUTES

ASSEMBLE STAND (FIG. A)

1.Unpack all parts and group by type and size. Refer to the parts list for correct quantities.

2.Attach one short upper support (1) to top of leg (2) using one bolt (3) and nut (4).

NOTE:

●Align detents in stand leg with support brackets to ensure proper ﬁt.

●Do not tighten bolts until stand is properly aligned (see step #8 before tightening).

3.Attach other end of short upper support to top of another leg using one bolt and nut.

4.Attach one short bottom support (5) to center of each leg using bolt (3) and nut (4). This completes the front frame section.

5.Assemble rear frame section in exactly the same manner.

6.Join front and rear frame assemblies using two long upper supports (6) and two long bottom supports (7), bolts and nuts.

7.Insert foot pad (8) into bottom of leg. Repeat for each leg.

8.Place stand on level surface and adjust so all legs are contacting the ﬂoor and are at similar angles to the ﬂoor, and detents in stand leg align with support brackets, then tighten all bolts.

NOTE: To avoid rocking, tighten all bolts.

Fig. A	9
Fig. A
	10

11

3

12

	4	6
		1
8	7	5
8
		2

WARNING

●The stand is designed only for using with scroll saw.

●Do not climb, sit or stand on the stand assembly.

●Do not use the stand on uneven or unstable surface.

MOUNTING THE SCROLL SAW (FIG. A, B)

1.To mount your scroll saw to the stand, position the leg stand (1) on a ﬁrm, level surface.

2.Matching the holes (2) in the scroll saw base with the holes in the leg stand, place the scroll saw on the stand.

3.Secure the stand and saw using the hex head bolts (9), ﬂat washers (10), sleeve (11) and nuts (12) provieded.

4.Tighten all four nuts.

NOTE: Do not over tighten nuts holding saw to stand. This may damage this saw base.

Fig. B

9

10

2

12

1

– 11 –

Image 11

Contents Mode D’EMPLOI ET Instructions DE Securite Contents Blade Product SpecificationsMotor English Power Tool SafetyGeneral Safety Instructions Before Using this Power Tool Hold Workpiece Firmly against the table top Scroll SAW SafetySpecific Safety Instructions for this Scroll SAW Think SafetyGuidelines for Extension Cords Electrical Requirements and SafetyGrounding Instructions Supplied Not Supplied Mm Hex Wrench Medium Screwdriver Accessories and AttachmentsTools Needed for Assembly Recommended AccessoriesCarton Contents Know Your Scroll SAW Woodworking Terms Glossary of TermsScroll SAW Terms Mounting the Scroll SAW FIG. A, B Assembly and AdjustmentsEstimated Assembly Time 15~20 Minutes Assemble Stand FIG. a Sawdust Collection Port FIG. E Blade Removal and InstallationMounting Scroll SAW to Work Surface FIG. C Blade Storage FIG. DPLAIN-END Blade Removal FIG. F, G, H PLAIN-END Blade Installation FIG. H, I, JPIN-END Blade Removal FIG. K, L PIN-END Blade Removal and InstallationSawdust Blower FIG. Q Blade Guard Foot Adjustment FIG. O, PBlade Selection FIG. R Variable Speed Control Knob FIG. S On I / OFF O Switch FIG. SOperation Replacing the Bulb FIG. SAngle Cutting FIG. U Freehand Cutting FIG. UInterior Cutting FIG RIP or Straight Line Cutting FIG. WReplacing Carbon Brushes FIG. Y, Z MaintenanceGeneral Symptom Possible Causes Corrective Action Troubleshooting GuideLames Fiche Technique DU ProduitFrançais MoteurDécouper Consignes DE Sécurité Générales ÀRespecter Avant D’UTILISER LA Scie 26.SÉCURITÉ Avant Tout Consignes DE Sécurité Spécifiques À Cette Scie À DécouperTenir Fermement LE Matériau À Scier Mise EN Garde Directives DE Mise À LA TerreDirectives Concernant LES RallongesFourni Not Fourni AccessoiresOutils Requis Pour Assemblage Pied Contenu DE LA BoîteART Description Quantité Apprendre À Connaìtre LA Scie À Découper Termes DE Menuiserie GlossaireTermes Relatifs AUX Scies À Découper Remarque Assemblage ET RéglagesCompartiment DE Rangement DES Lames FIG. D Pose DES Lames Ordinaires FIG. H, I, J Pose ET Dépose DES Lames À Ergot FIG. F, G, HDépose DES Lames À Ergot FIG. K, L Pose ET Dépose DES Lames À ErgotSouffleur DE Sciure FIG. Q Réglage DU Pied DU PROTÈGE-LAME FIG. O, PChoix DES Lames FIG. R Interrupteur Marche I -ARRÊT O FIG. S Remplacement DE L’AMPOULE FIG. SRecommandations Pour LES Coupes UtilisationCoupe À Main Libre Coupes EN Biais FIG. UCoupe Intérieure FIG Coupes DE Refente OU EN Ligne Droite FIG. WQuantité Description Généralités Remplacement DES Balais DE Charbon FIGEntretien Problèmes Causes Possibles Remèdes Guide DE DépannageExtractor DE Polvo Especificaciones DEL ProductoEspañol Motor MesaHerramienta Eléctrica Seguridad DE LAS HerramientasInstrucciones Generales DE Seguridad Antes DE Utilizar EstaCaladora Segurida DE LA Sierra CaladoraInstrucciones Específicas DE Seguridad Para Esta SierraFunciona, a ﬁ n de proteger al operario de posibles Seguridad Y Requisitos EléctricosInstrucciones DE Puesta a Tierra Directrices Para EL Cable DE ExtensiónSuministran No se suministran Accesorios Y AcoplamientosAccesorios Recomendados Soporte Contenido DEL EmbalajeDesembalaje Y Comprobación DE SU Contenido Desembalaje DE SU Sierra DE MarqueteríaFamiliarícese CON SU Sierra Caladora Botón DE Bloqueo DEL PIE DEL Guardahojas Glosario DE TerminosTérminos DE LOS Componentes DE LA Sierra Términos DEL Trabajo CON MaderaMontaje DE LA Sierra DE Marqueteria FIG. A, B Montaje Y AjustesNota Almacenamiento DE Hojas FIG. D Montaje DE LA Sierra Caladora AL Plano DE Trabajo FIG. CMontaje DE LA Hoja DE Extremo Liso FIG. H, I, J Desmontaje DE LA Hoja DE Extremo Liso FIG. F, G, HMontaje DE LA Hoja CON Extremo DE Pasador FIG. M, N Desmontaje Y Montaje DE Hojas CON Extremo DE PasadorDesmontaje DE LA Hoja CON Extremo DE Pasador FIG. K, L Extractor DE Serrín FIG. Q Regulación DEL PIE DEL Guardahojas FIG. O, PSelección DE LA Hoja FIG. R Boton DE Control DE Velocidad Variable FIG. S FuncionamientoCambio DE LA Bombilla FIG. S Interruptor DE Encendido I /APAGADO O FIG. SCorte EN Ángulo FIG. U Corte a Mano FIG. UCorte Interior FIG Regado O Corte EN Línea Recta FIG. WReemplazo DE LAS Escobillas DE Carbon FIG. Y, Z MantenimientoGeneralidades Problema Causa DEL Problema Solución Recomendada Guia Para LA Solucion DE ProblemasAlways order by I.D. Number Parts ListParts List for Schematic Scroll SAW Model NO. CWScroll SAW Model NO. CW Parts List for Stand Hitachi Koki Canada Co