Hitachi Koki USA CW 20 RIP or Straight Line Cutting FIG. W, Interior Cutting FIG

Page 18

English

RIP OR STRAIGHT LINE CUTTING (FIG. W)

WARNING

To avoid injury from accidental starting, make sure the switch is in the OFF (O) position and the plug is not connected to the power outlet before moving, replacing blade or making adjustments.

Tools Needed (Not Included)

QUANTITY DESCRIPTION

2Small C-clamps

1Ruler or Measuring Tape

112-inch Straight Scrap of Wood (Thickness to match workpiece)

1.Raise the blade guard foot (1) by loosening the blade guard foot lock knob (2) on the right side of the upper arm. Measure from the tip of the blade (3) to the desired distance. Position the straight edge (4) parallel to the blade at that distance.

2.Clamp the straight edge to the table (5).

3.Recheck your measurements, using the workpiece to be cut, and make sure the scrap wood is secure.

4.Position the workpiece against the blade and place the blade guard foot (1) slightly above the top surface of the workpiece.

5.Secure the blade guard foot in place by tightening the blade guard foot lock knob.

6.Remove the workpiece from the blade prior to turning the scroll saw ON (I). Set the desired speed by turning the control knob clockwise or counterclockwise.

WARNING

In order to avoid uncontrollable lifting of the workpiece and to reduce blade breakage, do not turn the saw ON

(I) while the workpiece is against the blade.

7.Position the workpiece against the straight edge (4) prior to touching the leading edge of the workpiece against the blade (3).

8.Slowly feed the workpiece into the blade, guiding the workpiece against the straight edge and press the workpiece down against the table while cutting.

WARNING

Do not force the leading edge of the workpiece into the blade. The blade will deflect, reducing accuracy of cut, and may break.

9.When the cut is complete, move the trailing edge of the workpiece beyond the blade guard foot. Turn the scroll saw OFF (O).

NOTE: When cutting a narrow workpiece, use push sticks.

Fig. W

 

 

I

2

1

3

5

 

 

4

 

 

INTERIOR CUTTING (FIG. X)

1.Lay out the design on the workpiece (1). Drill a 1/4-inch hole into the workpiece.

2.Release the quick release tension lever (2), and remove the blade (3). Refer to BLADE REMOVAL AND INSTALLATION.

3.Place the workpiece on the saw table with the hole

(4) over the access hole in the table (5).

4.Install the blade (3) through the hole in the workpiece and lower the quick release tension lever (2).

5.Follow steps 3-8 under FREEHAND CUTTING OPERATIONS.

6.When finished making the interior scroll cuts simply turn the scroll saw OFF (O). Remove the blade from the blade holder and remove the workpiece from the table.

Fig. X

2

I

3

4

5

1

– 18 –

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Mode D’EMPLOI ET Instructions DE Securite Contents Product Specifications MotorBlade Power Tool Safety General Safety Instructions Before Using this Power ToolEnglish Think Safety Scroll SAW SafetySpecific Safety Instructions for this Scroll SAW Hold Workpiece Firmly against the table topElectrical Requirements and Safety Grounding InstructionsGuidelines for Extension Cords Recommended Accessories Accessories and AttachmentsTools Needed for Assembly Supplied Not Supplied Mm Hex Wrench Medium ScrewdriverCarton Contents Know Your Scroll SAW Glossary of Terms Scroll SAW TermsWoodworking Terms Assembly and Adjustments Estimated Assembly Time 15~20 Minutes Assemble Stand FIG. aMounting the Scroll SAW FIG. A, B Blade Storage FIG. D Blade Removal and InstallationMounting Scroll SAW to Work Surface FIG. C Sawdust Collection Port FIG. EPLAIN-END Blade Installation FIG. H, I, J PLAIN-END Blade Removal FIG. F, G, HPIN-END Blade Removal and Installation PIN-END Blade Removal FIG. K, LBlade Guard Foot Adjustment FIG. O, P Blade Selection FIG. RSawdust Blower FIG. Q Replacing the Bulb FIG. S On I / OFF O Switch FIG. SOperation Variable Speed Control Knob FIG. SFreehand Cutting FIG. U Angle Cutting FIG. URIP or Straight Line Cutting FIG. W Interior Cutting FIGMaintenance GeneralReplacing Carbon Brushes FIG. Y, Z Troubleshooting Guide Symptom Possible Causes Corrective ActionMoteur Fiche Technique DU ProduitFrançais LamesConsignes DE Sécurité Générales À Respecter Avant D’UTILISER LA ScieDécouper Consignes DE Sécurité Spécifiques À Cette Scie À Découper Tenir Fermement LE Matériau À Scier26.SÉCURITÉ Avant Tout Rallonges Directives DE Mise À LA TerreDirectives Concernant LES Mise EN GardeAccessoires Outils Requis Pour AssemblageFourni Not Fourni Contenu DE LA Boîte ART Description QuantitéPied Apprendre À Connaìtre LA Scie À Découper Glossaire Termes Relatifs AUX Scies À DécouperTermes DE Menuiserie Assemblage ET Réglages RemarqueCompartiment DE Rangement DES Lames FIG. D Pose ET Dépose DES Lames À Ergot FIG. F, G, H Pose DES Lames Ordinaires FIG. H, I, JPose ET Dépose DES Lames À Ergot Dépose DES Lames À Ergot FIG. K, LRéglage DU Pied DU PROTÈGE-LAME FIG. O, P Choix DES Lames FIG. RSouffleur DE Sciure FIG. Q Utilisation Remplacement DE L’AMPOULE FIG. SRecommandations Pour LES Coupes Interrupteur Marche I -ARRÊT O FIG. SCoupes EN Biais FIG. U Coupe À Main LibreCoupes DE Refente OU EN Ligne Droite FIG. W Quantité DescriptionCoupe Intérieure FIG Remplacement DES Balais DE Charbon FIG EntretienGénéralités Guide DE Dépannage Problèmes Causes Possibles RemèdesMotor Mesa Especificaciones DEL ProductoEspañol Extractor DE PolvoSeguridad Antes DE Utilizar Esta Seguridad DE LAS HerramientasInstrucciones Generales DE Herramienta EléctricaSeguridad Para Esta Sierra Segurida DE LA Sierra CaladoraInstrucciones Específicas DE CaladoraDirectrices Para EL Cable DE Extensión Seguridad Y Requisitos EléctricosInstrucciones DE Puesta a Tierra Funciona, a fi n de proteger al operario de posiblesAccesorios Y Acoplamientos Accesorios RecomendadosSuministran No se suministran Desembalaje DE SU Sierra DE Marquetería Contenido DEL EmbalajeDesembalaje Y Comprobación DE SU Contenido SoporteFamiliarícese CON SU Sierra Caladora Términos DEL Trabajo CON Madera Glosario DE TerminosTérminos DE LOS Componentes DE LA Sierra Botón DE Bloqueo DEL PIE DEL GuardahojasMontaje Y Ajustes NotaMontaje DE LA Sierra DE Marqueteria FIG. A, B Montaje DE LA Sierra Caladora AL Plano DE Trabajo FIG. C Almacenamiento DE Hojas FIG. DDesmontaje DE LA Hoja DE Extremo Liso FIG. F, G, H Montaje DE LA Hoja DE Extremo Liso FIG. H, I, JDesmontaje Y Montaje DE Hojas CON Extremo DE Pasador Desmontaje DE LA Hoja CON Extremo DE Pasador FIG. K, LMontaje DE LA Hoja CON Extremo DE Pasador FIG. M, N Regulación DEL PIE DEL Guardahojas FIG. O, P Selección DE LA Hoja FIG. RExtractor DE Serrín FIG. Q Interruptor DE Encendido I /APAGADO O FIG. S FuncionamientoCambio DE LA Bombilla FIG. S Boton DE Control DE Velocidad Variable FIG. SCorte a Mano FIG. U Corte EN Ángulo FIG. URegado O Corte EN Línea Recta FIG. W Corte Interior FIGMantenimiento GeneralidadesReemplazo DE LAS Escobillas DE Carbon FIG. Y, Z Guia Para LA Solucion DE Problemas Problema Causa DEL Problema Solución RecomendadaScroll SAW Model NO. CW Parts ListParts List for Schematic Always order by I.D. NumberScroll SAW Model NO. CW Parts List for Stand Hitachi Koki Canada Co
Top Page Image Contents