RIDGID 122XL manual Accessories, Reaming I.D. of Tube, Cleaning Inside of Fittings

Page 10

122XL Copper Cutting and Prep Machine

Reaming I.D. of Tube

NOTE! Maximum capacity of the reamer is 2” diameter tubing.

1.Turn ON/OFF switch to ON position.

2.Remove burrs on inside of tube by placing tube over reamer cone and gently applying pressure (Figure 8). Long lengths of tubing should be supported by pipe stands.

WARNING Keep fingers away from the reamer cone. Keep hands away from ends of tube that may have burrs or sharp edges.

3. Turn ON/OFF switch to OFF position.

Figure 8 – Reaming I.D. of Tube

Cleaning Inside of Fittings

NOTE! Fitting brushes are an accessory and sold sep- arately.

1.Check that brush is the correct size for the fitting diameter. Install correct size fitting brush if necessary.

NOTE! Use 3fitting brush on both 3and 4diameter fittings.

Do not use a 4fitting brush on this machine. Will interfere with the tubing during cut-off.

2.Turn ON/OFF switch to ON position.

3.Push fitting over fitting brush (Figure 9). Hold fitting securely to prevent rotation. For 4fitting, rotate to clean entire inside diameter.

CAUTION Keep fingers away from brush.

4. Turn ON/OFF switch to OFF position.

Figure 9 – Cleaning Inside of Fittings

Accessories

WARNING

Only the following RIDGID products have been designed to function with the No. 122XL Copper Cutting And Prep Machine. Other accessories designed for use with other tools may become hazardous when used on this machine. To prevent serious injury, use only the accessories listed below.

Accessories, Replacement Cutter

Wheels, Cleaning Brushes For No.

122XL Cutting and Prep Machine

Cat. No.

Description

36662

Model 301A Foot Switch – 120V

93717

1/2Fitting Brush (Pkg. of 3)

93722

3/4Fitting Brush (Pkg. of 3)

93727

1Fitting Brush (Pkg. of 3)

93732

11/4Fitting Brush (Pkg. of 3)

93737

11/2Fitting Brush (Pkg. of 3)

93742

2Fitting Brush (Pkg. of 3)

12638

21/2Fitting Brush (Pkg. of 3)

12643

3- 4Fitting Brush (Pkg. of 3)

93747

Quick-Change Adapter f/Fitting Brush

93712

Fitting Brush Holder

33551

Cutter Wheel f/Copper and Stainless Steel

10343

Wheel Pin for 33551 Cutter Wheel

42295

Outside Diameter Cleaning Brush

42360

1206 Stand

 

 

Pipe Stands Recommended For Use with No. 122XL Copper Prep Machine

VJ98 Cat. No. 56657

VJ99 Cat. No. 56662

RJ98 Cat. No. 56667

RJ99 Cat. No. 56672

8

Ridge Tool Company

Image 10
Contents 122XL Copper Cutting and Prep Machine Table of Contents 122XL Copper Cutting and Prep Machine Electrical Safety General Safety InformationWork Area Safety Personal SafetySpecific Safety Information Description, Specifications and Standard EquipmentAccessories Machine AssemblySpecifications Standard EquipmentMachine and Work Area Set-Up Machine InspectionMounting on No Stand Operating Instructions Cutting TubeCleaning/Deburring O.D. of Tube Turn ON/OFF switch to the OFF positionCleaning Inside of Fittings AccessoriesReaming I.D. of Tube Maintenance Instructions Motor Machine Storage Service and RepairWiring Diagram 115V 60Hz 100V 50/60Hz 220 240V/50HzMachine à couper et à préparer le cuivre modèle 122XL Table des matières Sécurité électrique Consignes générales de sécuritéSécurité du chantier Sécurité individuelleUtilisation et entretien des outils Service après-venteConsignes de sécurité particulières Sécurité de la machineSpécifications AccessoiresDescription, spécifications et équipements de base Equipements de baseAssemblage de la machine Installation sur trépied typeAccessoire facultatif Inspection de la machinePréparation de la machine et du chantier Utilisation de la machine Coupe des tuyauxNettoyage et ébarbage de l’extérieur du tuyau Alésage de l’intérieur des tuyauxAccessoires Nettoyage de l’intérieur des raccordsEntretien Schéma électrique Stockage de la machineEntretien et réparations MoteurMáquina cortadora y preparadora de tubos de cobre 122XL Índice Seguridad eléctrica Información general de seguridadSeguridad en la zona de trabajo Seguridad personalServicio Información específica de seguridadUso y cuidado de la máquina Seguridad de la máquinaEspecificaciones Descripción, especificaciones y equipo estándarDescripción Equipo estándarEscobillas limpiafittings y su portaescobillas Montaje de la máquinaRevisión de la máquina Montaje en el Soporte NoPreparación de la máquina y de la zona de trabajo Instrucciones de funcionamiento Corte de tubosMueva el interruptor de ON/OFF a la posición de OFF apagado Escariado del diámetro interior del tubo AccesoriosLimpieza del interior de un fitting Instrucciones para el mantenimiento Almacenamiento de la máquina Servicio y reparacionesDiagrama de cableado 115V, 60 Hz 100V 50/60Hz 220 240V/50HzMáquina cortadora y preparadora de tubos de cobre 122XL Ridge Tool Company